i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
After updating from THREAD SDK 2.0 to SDK 3.1 I am getting NRF_ERROR_NO_MEM in nrf_sdh.c.
The project is based from the multiprotocol BLE thread dynamic example.
The code...
I'm creating a ble central device that receives instructions via UART on which device to connect to and which UUID to write to.
I'm able to connect to a peripheral device...
Hi,
I am working with NRF52840 and want to encrypt my saved data with AES using CC310 cryptocell.
I am working with nrf_crypto_aes frontend to do AES.
I want to know...
Hello,
I'm trying to build and run 'secure_bootloader/pca10040_ble_debug/armgcc/' example and it seams that it stops with some hard fault:
Remote debugging using localhost...
Hi,
I tried to evaluate the light switch demo using the boards that I have to my disposal.
These are 1 nrf52-DK and 2 nrf52840 Dongles.
I wanted to use one dongle...
in application design , this pin is not connected to VDD , but application board works well ,
application's power range is 2.2V - 3.3V (AAA batteries), max current consumption...
I'm attempting to troubleshoot why my HM18 doesn't connect to the ESP32 over BLE. I'm now deep in the rabbit hole that is BLE sniffing so now I'm trying to determine if the...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
What is the least expensive J-Link Model is required to program a nRF52840 on a custom commercial PCB?
I see that it is a ARM Cortex-M4 core, but I want to double-check...
Hi
Im using nRF52832-QAAB0. SDK 15.3. Softdevice is running.
With debugger connected, calling nrf_pwr_mgmt_shutdown(NRF_PWR_MGMT_SHUTDOWN_STAY_IN_SYSOFF) will assert in...
Hi everyone. Do you know any example of some over the air FW upgrade of nrf52832 chip via ESB protocol. As I understand it should be some combination of bootloader with DFU...
Hello,
We have selected nRF solution for our next product line and currently evaluating the software/SDK setup for that.
We are testing following SDKs:
nRF5_SDK_15.2...
