Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hello,
I use the LAIRD module BL652 with an nRF52832 with the SoftDevice 14.0.0 (old version…).
The application use the BLE with the SoftDevice.
We have mesured the...
Hello,
Here i are using nRF52832 ,softdevice S132 and mesh sdk v3.0.0
For my Application,i need to go with DFU.so i merged my application into the example code of DFU...
Hello,
Does anyone know if the FreeRTOS port that's distributed with the nRF5_SDK_14.2.0 is intended to support nRF52810 chips (which have no hardware FPU)? I started working...
SDK 14.2 keil5
I want to run freertos with nrf52810.but I did not find any example .
Is there anyone have tried this?
I downloaded nrf52832 code(ble_app_hrs_freertos...
Hello All,
I have looked around for answers to my specific issue, however I did not seem to find one that aided me enough to fix my issue.
I have created a BLE profile...
Hello,
SDK 15.2, SD 6.1.0 with PCA10056 1.0.0, 2018.20. nRF Connect App v4.22.3. Pixel XL.
I'm running into an issue with my application where the phone disconnects after...
Using: Linux (Ubuntu 18.04), gcc/Eclipse, nrf52840, v15.3.0 SDK, SD 6.1.1
It has been a real bear of time using the SDFU in the newest version of the SDK. There were a lot...
Dear support,
Our team is considered doing their own smart watch, so i found that nRF52 chip is a nice solution. Just before we start, i would like to do some basic questions...
When we ported our FreeRTOS based project to SDK 15.3 from 15.2, we noticed a big jump in the CPU Usage. It turned out that the issue was in SDK 15.3's freertos port_cmsis_systick...
Hi nordic,
I send multiple bytes but always only receive packets of length = 1. For example in the picture, I sent 2 bytes 0x68, 0x69 ('DE') but only received the first...
Hi
What is the difference between ble_nus.c and ble_nus_c.c?
because i went through both the files and i felt both files are almost same except an extra function(db_discovery...
Hello, I bought a nRF52832 Breakout Board from SparkFun. from their tutorial, you can program this board using the serial bootloader and the Arduino IDE. However, aside for...
I am trying to operate a BLE5 sniffer with nrf52840dk
After connecting the dk to nrf connect desktop and programming it with a wrong code (by mistake), it is not able to...
