Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I tried to increase the bootloader size by reducing IROM start address and increasing size but I always get the same error:
.\_build\nrf52832_xxaa_s132.axf: Error: L6407E...
I would like to perform FDS garbage collection only when it is close to being full. I can read the fds_stat to see the number of words used and the words freeable but what...
Hi all,
I would like to get the complete name from the connected peripheral by reading the device name characteristic (0x2A00) in the Generic Access Service (0x1800). I...
I want to use sys_time_get() on my ble app in SES env. but it looks like sdk 14.2.0 doesn't support sys_time_get() on SES env. So I'd like to use the similar function such...
Hi
Am new to the nrf52382 , Am trying to establish connection between nrf52382 DK as peripheral and nrf connect app as central,
Am unable to connect it .Please debug...
Hi, I am using nRF52832 with sensor, nfc , Softdevice S132 v6.1.0 and SDK 15.2.0 to advertising packets .The sensor is interfaced with nrf52832 using twi interface. I have...
I learned from the following support ticket link that for adding a pre-bonded LTK to the nRF52 bonding store, I can call pm_peer_new().
https://devzone.nordicsemi.com/f...
Hi,
I am trying out the udp_with_psm example from: https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/udp_with_psm as a first step in sending...
Hi Team,
I planned to have product with this nRF52832 chip and now development was getting stopped because of known issues on SAADC on this nRF52832 chip. When I am seeing...
Hi. I am developing application that should work both ANT+ and Bluetooth. For bluetooth connection I am testing with nrf connect for pc, but I was wondering if there is similiar...
Ran in to a build error when using nrf_fstorage_nvmc.c: \components\libraries\fstorage\nrf_fstorage_nvmc.c(128,19): error : conflicting types for 'write'
nrf_fstorage_nvmc...
Hi,
I'm working with the latest software version of nrf52840.
Can you kindly specify the exact addresses of:
1. Flash usage of Softdevice
2. RAM usage of Softdevice...
Hi Team,
We are currently validating a BLE enabled embedded device. The device has an ARM Cortex M0 chipset and uses Dialog Semiconductor for BLE.
Could you please let...
When using the 0.7.0-15.alpha firmware release. What is the best application side code to go with it. Should still tag v0.3 be used of: zephyr, nrfconnect and nrfxlib?
...
I now want to update the program in SDK14.2 to SDK15.2 through DFU, so softdevice, bootloader, app need to be updated, how should I operate? I first try to update the bootloader...
