We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
It is unclear for me why the following code look like this (conn_ble_gap_sec_keys.c, SDK15):
Is it logical that here the SER_MAX_ADV_DATA is used? is there actual advertising...
Hi , nrf connect V.2.5.0 in windows 10 64bit, fails to launch Bluetooth low energy app. "DEBUG UART read operation on port aborted" is the log info which i came to know from...
Hi,
I have a BLE sensor node (firmware not modifiable) that takes up a peripheral role and starts advertising when powered up. Typically, one can scan for the node from...
Hi All!
I have been working on bringing-up a custom manufactured nRF52832 board. I have with me 6 boards, the first 3 are working fine, the other 3 are not. In both cases...
Hello all,
I'm practicing creating my own service following instruction from this link: https://github.com/bjornspockeli/custom_ble_service_example
Now I stuck at part...
Hi everyone,
I have configured two UARTES , one using the app_uart library and another using nrf_serial library.
I am using SDK15.0 alongwith s140 softdevice with bluetooth...
Hi There,
What are the difference between system off, ram retention, RTC wakeup vs system on with ram retention, RTC wakeup vs FreeRTOS tickless with RTC wakeup? And what...
Hi team,
I noticed a very interesting incorrect pin description in the latest product specification of v1.2 for nRF52810, QFN32.
Above picture shows we have 2 p0...
I'm using the PCA10056 with an SD card connected via P1.12-P1.15. When I use the FatFs example of SDK12 PCA10028 it works fine. but when I use the FatFs example of SDK15.0...
Hello,
I've got the nrF52840 and would like to create a simple application to send temperature to my laptop. Then the next step would be to create some mesh network with...
Hello,
I am working on Custom BLE HID Keyboard. I am currently trying to understand working of program given by nordic in SDK-10.0.0. THere is one problem which I am facing...
Hi,
I've tried to implement the DFU_buttonless example to my development board. I programmed the bootloader and the settings-page. The bootloader detects the application...
I'm currently in the prototyping phase of getting two nDK52840 boards talking to each other. I currently have one board flashed with the central role, and another board flashed...
Hello.
What do I need to run this example called uart?
As far as I understand this should be simple echo program meaning what comes in goes out but I can not see anything...
