Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I used nRF52840 dongle device to run BLE multi-link Central and nrf52832 to run BLE Blinky example to test the communication of 20 nodes. How can I set and verify that...
We are using nRf52840 chip with Nordic SDK 15.0 version using SES IDE. When we use debug mode in build configurations program is not working or not debugging got error as...
Hello All,
We are trying to use nrf52810 with S112 soft device and 14.2 SDK.
We have problems with random disconnection with error number 8. This happens when central...
Hello,
I am attempting to run the Nordic-Thingy52-mesh-demo using nRF Mesh v 1.1.0 for Android but the nRF Mesh app's scanner cannot see my DKs. I can see the mesh from...
Hello All,
We are attempting to instrument our software and yours. The desired output is data for a call-graph list and time stamps for each entry and exit into a function...
Why does the pushing a button located at GPIO_9 not call the interrupt handler and therefore print the statement to RTT?
#include "GPIO.h"
#include "app_error.h"
#include...
We are currently using nRF51822-CEAA rev2 on the production boards. As this part is obsolete, I was made aware of nRF51822-CEAA rev3 as a replacement . So I have some questions...
Hello,
I have a nrf51822 application which is communicating with iOS (iphone) via BLE HID service. It's only purpose is to send a screen lock HID code to iPhone. The bad...
Hi,
I've been using nRFgo studio to program hex files to the board.
Most of the time it has been working trouble free.
However, a while ago we got one, and than one...
Hello,
I am trying to program my own provisioner. I am able to connect to a device, following this Provisioning Procedure .
How can I now configure the node? As far as...
Hi,
My team is building a wearable application similar to a smartwatch.
Our system requires two main operating voltages. 1V8 and 3V3. I was thinking that we would use...
Hi there,
I am using the nRF connect app on Android to see my dongle's name. I want the name to change every 5 seconds from one name to another. This is just for evaluation...
Our products are based on nRF52832 & nRF52840 and include display.
We use DFU mechanism for application update.
According to Nordic's documentation DFU supports multi...
I have an application running on an STM32L1 and want to adapt it to the nRF52832 w/ SDK 13.2.
This app read three analog sensors and send data to another device, using UART...
