Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When static authentication is used, it is my understanding that both the provisioner and the privisionee have a static preprogrammed key. The SDK says:
"The application...
Hi, starting from the demos on the devboard, I want to make a custom pcb work now. For that, I do not need UART/logging functions, which will otherwise cost me current consumption...
I use SDK15 and S132. I have examples\dfu\secure_bootloader\pca10040_ble loaded in my board. I can see it advertising when there is not valid app loaded.
Also, my app with...
Hello Nordic Team
I am working on zigBee project. I see there is uart example available in SDK which works BLE + end point. Is there any example available which works on...
Hi all!
I found solution for Xiaomi zigbee smart home sensors (gerkon, water sensor, pir motion, and other...) based on CC2530 zigbee shepherd and Trust Center Link Key...
I am doing a project with nRF24L01+ but i found out this is not certified chip to FCC. Is any other RF that is certified that i can replaced this RF24?
Hello,
I am creating a read-only characteristic with sd_ble_gatts_characteristic_add (specifically, characteristic_add). The value is 31 bytes.
On a Read Request, it is...
Hello
I would like to send my sensor data to a mobile application using BLE SDK 15. Someone suggested me to go through the BLE NUS SERVICE example which was a good one....
Hi,
I am new to Nordic development environment.
I am compiling the some code developed by vendor for NRF5 SDK 12.2.0
I am getting errors such as
Error1 snippet
...
Dear Colleagues,
I could use some help or ideas. I’m working on the link layer encryption of an open source Bluetooth stack. It starts to work! But, now I have the effect...
Using softdevice 6.1.0 and SDK 15.2:
Is it safe to use NRF_UICR->CUSTOMER[0] through CUSTOMER[5] for storing serial numbers?
It seems through in previous versions of SDK...
Hi All,
I have implemented the code for MASTER serial DFU in ST micro controller. which can send the app .bin file. I'm using 57600 baud and disable the flow control....
Hello,
I am using 15.2.0 SDK and 3.1.0 Mesh SDK.
I was trying to control two LED's on the nRF52DK using two generic level server models. I made following changes to the...
Hello. I got an nRF9160 DK with an iBasis eSIM that was already registered on an nRF Cloud account. Is it possible move the already activated eSIM to my Cloud account? I tried...
