But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I am creating a BLE program with ISP4520 which has nRF52832 implemented.
In terms of the program, it is a device that uses BLE communication with a PC, but when I use the...
Issue:
The OTBR could run with RCP versions built with SDK v2.3.0 and v2.4.2 but couldn't work with fw from SDK v2.9.0. Hence, I wanted to know which of the latest SDKs...
Hello,
I’m trying to obtain millisecond precision on nRF Connect using the MCU’s internal RTC.
My code:
After 131000 ms, a got:
Could someone help me find...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
Hi guys,
I am following DevAcademy lessons on nrf52833dk kit. I am testing the software on VsCode. SDK version is 2.7.0 and toolchain is 2.7.0. Board target is selected...
I have the nRF Hw v1, and it seems like I did something wrong with a Fw:
nRF is recognizable by a computer as the COM3/4/5 device:
And it is accessible with the nRF...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
Dear NRF Team,
I hope this message finds you well. I have been following the steps provided at the Dev Academy for the initial setup of the IDE. However, I have encountered...
Hi,
I'm trying to use the HCI UART sample to provide Bluetooth support through UART. At first I want to test it between two Nordic Boards, but later switch to another MCU...
Hi, I am facing an issue while integrating BLE with the rest of my code. The code crashes when I try to start BLE outside of main() .
Currently, I have placed the BLE initialization...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
You are trying to perform RSA encryption using CC312 on the nRF5340, but the function:
returns -147 (PSA_ERROR_NOT_SUPPORTED) when CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y and...
i am unable to build the unit test code with kernel file
FAILED: CMakeFiles/testbinary.dir/home/avinash/zephyrproject/unittesting/gce-source_code_latest/app/vipr/model/gas...
I'm trying to program an nRF54L15 on the nRF54L15PDK evaluation board with the DEBUG IN SWD pins (P15). On my setup I have a J-Link PLUS connected to P15 and a USB-C connected...
