Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello, I recently installed nrf sdk but I have trouble getting through getting started phase. I'm using ubuntu 24.04 and created workspace environment using CLI. Below is...
Hi I'm encountering an error while building Lesson 8, Exercise 1, Step 3 using the nrf7002dk/nrf5340/cpuapp target board. Below is the error message I received:
The same...
Hi, I have a BLE device in Observer role - it will constantly scan for Broadcasters broadcasting our unique UUID and put these scanned devices into a Ring Buffer.
The reason...
Hello,
I've encountered a condition where k_sleep(K_SECONDS(1)) never returns. Here is minimal example, reproduces both on nrf9160 and nrf9161:
Hangs up after printing...
Hi!
I am looking for a NRF52840+OpenThread+Azure IoT Hub SDK solution. Here is what I did so far. Nothing helped:
Thead CLI Example on NRF52840 + Border Router on...
Hello Nordic Team, We are currently using nRF52833-QDAA SoC for developing a new project that incorporates geofencing functionality using BLE.We . We tried using the example...
WE are working on nRF52832 and nRF5 SDK 15.0.0. Currently working on the BLE FOTA process and have successfully completed DFU up to this point. Our next goal is to save configuration...
Hi,
I just finished to setup everything to start using nRF Connect for VSCode Extension. I followed the "nRF Connect SDK Fundamentals" course in the DevAcademy.
I installed...
Hi,
nRF5 SDK for Thread and Zigbee supports DFU OTA over Thread, but I can't find the corresponding function in NCS.
If I want to implement DFU OTA over Thread in NCS...
Hi Team,
I'm analyzing to use nPM1300 PMIC in one of my projects. I planned to use the integrated Buck to power my on-board device. But, the calculated current consumption...
Hi Nordic team, I am facing an issue about using simple gpio to control external FEM( custom FEM model ) in NCS 2.7.0 & nrf5340. Here is background: 1. Our project is using...
On NRF52840, programming provision.hex with the command as follow:
%nrfjprog -f nrf52 --sectorerase --program provision.hex --reset --verify
On NRF54l15, the nrfutil...
Test platform: nRF54L15-DK
NRF Connect 2.9.0
When calling spi_write_dt, under the hood spi_nrfx_spim.c > configure is called to prepare the SPIM interface for a transmission...
I have an application that runs well on nRF52DK. It is like peripheral uart. I only use Tx/Rx and one LED. With OTA. All works as intended. I use NVS for parameters but nothing...
I've been trying to enable the watchdog as early as possible during boot. I haven't been able to find any way to configure the nrf52832 watchdog to enable itself prior to...
