When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey Nordic's technical team,
I'm trying to write and read via I2C to a component with two bytes registers. I tried the following method:
Then switched to this one: ...
Hello,
Using v1.9.1 nrfConnect and the Coordinator example on a nrf52840 -DK. From Nordic docs: I think I may be miss interpreting Zigbee Cluster spec... Below is example...
Good day
I have noticed that on my new DK boards if I touch VIO REF on P20 the PCB resets or stays in Reset if I keep touch the pin. My older boards never use to do that...
I want to set the GPIO of NRF52840 to the high resistance state. How do I set the GPIO of NRF52840 to the high resistance state, please help me,thanks!
Hi！
I'm working on direction finding using nrf connect sdk.
I have already make a tx (nrf52833) and a rx (nrf52833) and i succeed to receive the CTE and the IQ sampling...
I am working on adapting a project that compiles/flashes the code with a makefile that uses nrfjprog in a cmd line to program a blank nrf52480 with the softdevice and application...
Hi all
In nRF52840_PS Pin assignments sheet, some pins Recommended usage is " Standard drive, low frequency I/O only ", does that mean only low frequency (up to 10kHz...
Hi,
I am writing an application that reads data from the I2S interface, adds it to a queue and sends it via BLE (the code I have implemented so far is added at the end of...
Hello,
I am using the 802_15_4 MAC api to configure my device as a coordinator.
After it has been configured as a coordinator I want another device to connect to it...
I am using nRF52805(SDK 17.0.1 & S112) in my application development. Designed GATT Table Having some custom services with read, write & notify properties, And also, there...
I am testing advertising mechanism of nRF52832 device. But the following error occurred.
app: sd_power_system_off() failed, errCode=0x2006
The following is log messages...
It appears that an incorrect value is being used as the reset handler address so that the jump from bootloader to application is to the wrong address.
I am porting a bootloader...
I can not program the NRF52840 with the programmer software on windows 8.1. However when I run a virtual machine in oracle virtual box using windows 10 it works. I would rather...
