Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
The spec for the nRF52840 indicates a maximum power level of 8.0 dBm and -51dBm for 2nd order harmonics and -48dBm for 3rd order harmonics. What is the output power level...
Hello, is it possible to get the altium data from nRF52840 dongle (pca10059.SchDoc and PcbDoc) ? It's so time wasting to clone it from pdf. Thx. Ralf Adler
Hello Devzone,
I'm in the development stages on a battery based sensor device, utilizing nRF9160 System in Package for LTE-M connectivity and application processor. I have...
Hello Everyone,
We are using a nRF52810.
We have ran into an issue where our 32MHz XTAL can take longer than 400us and thus the Errata 3.6[68] CLOCK: EVENTS_HFCLKSTARTED...
Hello all!
I would like to use the PWM driver, yes, the hardware that is on board the chip. To get going certain code parts from the PWM driver that comes with the SDK,...
I would like to set the radio channel using 'uint32_t nrf_esb_set_rf_channel ( uint32_t channel ) '.
In 'nRF52840 Product Specification v1.7', '6.20.12.2 Operating frequencies...
Hello !
1.
In nRF21540 PS current consumption in TX mode is specified like this :
TX_20dBm State: TX POUT = 20 dBm 110 mA
But it is not clear if it depends from actual...
Hello everyone,
I am working with the SDK v17.1.0 with the DK nRF52832 with the examples of ble_app_uart and ble_app_uart_c.
I want to send an array "data_array" of uint8_t...
Hi,
the tool chain of NCS1.9.0 is at /opt/nordic/ncs/v1.9.0/toolchain
I just install NCS2.0.0 by NRF Connect Desktop.
However, I found there is no "toolchain" in /opt...
Hi,
We need help in getting an system call / API in Zephyr which updates the consumption of memory ram and flash
can you please suggest any mechanism which verifies...
I am using nRFConnect on windows 10 with the nRF540 Dongle for the first time.
I am successfully able to connect and view parameters on the nRF52832 using the Dongle.
...
Hello,
In my project i am using nr52840 actually its a custom board and i want to send the sensor data to custom app sometimes data updating and sometimes data not updating...
I am try to flash BLE SDK binary by Nordic, but using --sectorerase --verify with --reset seems to fail :
Two options combined :
I'm using the nRF51 SDK version 17...
Hi
I am developing for the nrf52832, S132, SDK17, trying to set up a SAADC multiple channel scan, however at times I will wish to only sample one channel, specifically ...
