i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello,
I would like to implement an I²C communication between a nrf52840 and a MCP3221 (which is an ADC).
The first 7-bit of the MCP3121 are 0b1001101. I guess the slave...
Hi!
I have a custom board based mostly of the nrf9160DK, where I need communication between nrf52849 and nrf9160 processor.
I have used the code from this ticket that...
Hi,
I'm using the PCA10056 dev kit and nRF5_SDK_17.0.2. I am aiming to connect multiple initiators to acceptor using Initiator and Acceptor examples. So far I've been able...
Hi There,
When I am trying to write code, I am not clear about the meaning of the code " bearer_adtype_add( BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME ); "
I try to check the...
I'm using the Zephyr provided WS2812 LED driver (SPI). I am noticing some strange behavior when my chain-length property is greater than 10.
I connected a digital logic...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hello
When I output some data using a 'LOG_xxx' macro, I do get debug information over the RTT console like this:
But as you can see there are some extra bytes in front...
Hello,
I wish to send SPI message by 2 Bytes per once, total 102 bytes.
Basically SPI works fine.
I wonder if there is way to reduce inter SPI time. It measured 18u...
Hi,
We are looking at porting the Tuya BLE SDK to the Nordic platform and on reviewing the documentation we have identified that the SDK uses two 16bit service UUIDs:
...
Most of the examples and posts are about the libuarte async driver, but I am using the basic libuarte_drv (not async) and running into difficulty. Without any concrete example...
Hello fellow developers,
I have purposefully not connected any sensor to my nrf52832 dev. board to see if the example program logs "no device found". Once the application...
Hi,
I have nRF52840 DK, nRFConnectSDK v 1.7.0-rc2,
I compiled iso_broadcast and iso_broadcast_benchmark projects: ( no changes are made)
Here is the run log:
//==...
Hello, I am starting to learn about the nrf9160DK and I found myself forced to use Zephyr while reading through the documentation. I would like to know if there is a way to...
Hi,
I am trying the new nRF connect extension for VSC. Great direction. Hope it takes off.
For those interested, the announcement and details are at: https://devzone.nordicsemi...
