This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Backround: We are planning to use TF-M with a two-stage bootloader (NSIB & MCUBoot) using dual-slots for secure and non-secure images. We need to support configurable fixed...
Hello Devzone,
In our product we are working with a nRF52840 microcontroller and periodically transmitting large sums of data to a PC or a phone.
We noticed that over...
Hi All,
I have designed my custom pcb board for nrf52811. With the Jlink the IC is detected in visual studio code also it gets programmed. But i did not see its working...
Hello,
I am currently working on a project that involves interfacing the TLV493D 3D magnetic sensor with the nRF52832 microcontroller. I would appreciate any guidance or...
Hi
We use the nRF52832 for an NFC device. The device is 99.9 % in the system off state to save power as much as possible. because the device is power by a button cell battery...
Hi
I'am using nRF util version 6.1.7 for a long time to generate a DFU packages. I need to debug my ble data so i thought of using ble sniffer from nrf util. But the ble...
Hello! We have a project under nRF Connect SDK and Zephyr. It uses Bluetooth central and peripheral role (GATT client and server).
The project works good under SDK v2.7...
Hi,
I'm trying to connect to the nRF52840 dongle using nRF Connect for Desktop Programmer v4.5 on MacOS 15.2 so I can update the firmware. The dongle has the red flashing...
I've then tried both the command " nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded" as well as "nrfutil ble-sniffer sniff --port /dev/ttyACM0 --coded --scan-follow-aux...
Helo,
I lost the PUK to my iBasis SIM, so I can't register it on nrfCloud.com for my 9160. Is there a way to recover it or do I need to buy a new one? (If so, where?)...
I tried to write the following simple '.overlay' file:
However, I am getting the following error:
but if you look inside the .dts files provided by the 'nrf52dk' I...
Hi everyone,
I’m working on a Zigbee application using the nRF52840, and I’ve been experiencing periodic reboots that I cannot figure out how to resolve. I’ve already updated...
Hello. I have a question about the development environment when developing using nrf.
When you build a new board and make firmware without using dk or ek, do you usually...
Hello everybody! There is a problem and help is needed. With the help of hardware timers, I need to generate a signal with a given accuracy. The frequency is 998 Hz. I'm using...
We are working on developing wearable device (like band) with cellular-IoT network connectivity. Considering available features and size, nRF91 series seems to be a good choice...
