Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hello everyone,
I am currently in the process of designing a prototype using the nRF9160 and I use the Nordic-Thingy91 as a reference for some parts. The Thingy91 uses the...
Is there any supporting documentation or information about remote assignment of receivers.
The only reference I have been able to locate is sparse and not backed by anything...
Hi guys,
I'm pretty new in embedded development without using an Arduino. I tried to use the sensor APIs of BMI270 and BMP388 recently, but didn't get it to work.
The...
HI All,
Could you please share the details for the below s on Nordic controller MCU nRF52833-QDAA to receive quotation on BLE_SIG certification,
QDID for Link Layer...
Hi,
I have a custom board running with the nrf52832. To program it I'm using the nrf52DK board with the PCA10040 and the bootloader is based on the one found in examples...
DK : 52840
case :
we make 52840 enter active scan state and know other broadcaster devcice mac,
can we use scan filter policy filter this broadcaster devcice ,and only...
(1) I connected Nordic nRF52810 device to ipad (version: 13.5.1) (ipad uses app for connection). At this time, a pop-up window appears asking if I want to pair the devices...
Good morning. I want to take ADC 12bit/1k sampling input and send uart and bluetooth. uart works fine, but there is a problem with losing data in bluetooth transmission. ...
During testing of various combination of BLE Mesh Provisioning, I found a couple of bugs in dk_prov.c
If you Disable all OOB options for no OOB, it does not work properly...
I'm using nrf_pwr_mgmt_shutdown to shut down the system to wake on interrupt. 17.0.2 SDK and 7.2.0 softdevice. When I step through the code with a debugger, it gets to sd_power_system_off...
My device is powered by an electromagnetic field from the 10 kilovolt line, which cannot deliver much power. When connected to a zigbia network, nrf52840 consumes too much...
I want to receive only 1 byte (Master in Slave out) without sending any bytes using using SPI. However when I monitor the SPI clock it produces 16 clock pulses. Although my...
Hello, How do disable code optimization in SES Nordic Edition when using nRF Connect SDK? I can't find "Options - Code Generation - Optimization Level" as when using nRF5...
Dear Sir,
I am trying to run example with NRF91 DK MQTT simple and I am able to connect with LTE network. as shown in below screenshot.
But as shown in the screen...
Hello, All
I go through datasheet of nRF5284o QFN73 IC. But i can't found which pins are used as uart /spi/i2c/pwm/timer/ I2S in pin description. Because pin assignment...
