Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi all,
Due to wrong pin assignment on my PCB I am currently bit banging a uart on two P2 pins using the FLPR core. The read bytes and bytes to send are communicated via...
Hello,
after a longer time, I wanted to use nRF Connect for Desktop again, to figure out what exactly my device under development is advertising. I upgraded to the latest...
Back in SDK 17 or so there were code samples for both the client and server side of the LED button service.
What happened to the client/central example when you migrated...
Description
I'm working on a battery-powered application where WiFi needs to be shut down between cloud sync intervals. I'm following the same pattern as the wifi/shutdown...
Hi,
working with nRF52840 with S140 v7.2.0, not sure about SDK version. VS Code + ARM GCC + LD Gold linker.
I changed stack and heap sizes via __HEAP_SIZE and __STACK_SIZE...
We are experiencing an issue with high current consumption when using the nPM1300 powered by a battery. In Hysteretic mode, the battery current draw measures 109 µA. However...
Hello Nordic Team,
We are currently working with the nRF54LM20B device and would like to understand whether Bluetooth Channel Sounding is supported on this SoC.
Specifically...
Hi：
What is the maximum number of targets that a DFU distributor can support for simultaneous upgrade, and what is the upper limit? I haven't found any detailed explanation...
I'm trying to put my code on a RAM/ROM diet and cut out any extra cruft so it will fit in an nRF52832. It used to fit with older SDKs, but not with the newest (v3.2.3).
...
Hello,
I am measuring RSSI values with nrf_modem_dect_phy_rssi(...) from the DECT PHY firmware.
The nrf_modem_dect_phy_rssi_event refers to positive values being saturated...
Hello, I have a particularly weird problem that I can't figure out how to solve. I was using the 52833 DK for software development and the onboard leds were blinking perfectly...
Hi.
I'm fighting to get an i2c scanner (re)expose external devices' hex addresses on an Xiao nrf52840 board under VsCode nrfConnect (the basic board, not the Sense version...
Hi,
we are designing a custom board based on the nRF54L15 QFAA (QFN48) using a chip antenna with coplanar waveguide feed on a 4-layer PCB.
In the Nordic reference design...
Hello, We're improving a battery-powered (CR2032) sensor tag based on an NRF52833 with a 868 MHz transceiver. We want to use the nPM2100 PMIC and would like to optimize the...
Dear Nordic Team,
We are seeking assistance in resolving a significant power consumption gap observed in our nRF9151-based asset tracker. While our lab testing suggests...
