Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi, I'm trying to using SEGGER IDE to program the nRF52840 whit both Zephyr RTOS and Nordic SDK accessible to my project. I have followed the guide on https://developer.nordicsemi...
Hi I still have problems with this board. I check it at my nRF dealer and it works. Yesterday I run it on an another PC and it works well:
But today at the same PC it...
Hello,
I am trying to implement the Peer Manager for bonding and pairing on my central device (nrf52840 Dongle) using SDK 15.3. I based my project off of the ble_app_uart_c...
Hello Nordic Semiconductor Community,
I do run mqtt_simple example successfully on my nRF9160 DK with modem firmware v1.1.1 and NCS tag v1.2.0.
Now I am connecting mqtt_simple...
Hi, I am using nrf52840 DK to create the uart ble app. The starting point is ble_app_uart example from SDK52 15.3. I changed pin configuration for uart so I can have RX and...
Hello,
I am looking into adding a whitelist to my central device to stop scanning devices I am disinterested in, however, I have a few questions and concerns about them...
Hi,
I saw the errata for bad onboard GPS antenna performance in nrf9160 DK v0.8.2 and 0.7.0
Was the problem fixed in 0.8.3, or is 0.8.3 still affected?
Thanks.
Hi,
I am using the nrf5 SDK for Mesh v4.0,
Windows 10,
4 DevKits PCA10056.
I have 2 DevKits as LPN (from the experimental_lpn example) and 2 DevKits as FNs (friend...
Hi,
I have a issue with the output regulation of REGOUT0.
I have a custom board based on the NFR52840-CKAA (revision D). I designed it in high voltage mode because I have...
Hi, I'm getting a crash when discarding an advertising packet.
Roughly what I do is:
Which crashes at advertiser_packet_discard().
GDB trace:
It looks like packet_buffer_pop...
When and by what logic Peer Manager performs garbage collection on FDS?
I have a single number stored also in FDS and I’m wondering if gc performed by Peer Manager will...
Hello,
I'm still just starting to deal with Zigbee and I have a question. I use 2 nRF52840 chips. One as a Zigbee Coordinator (CLI in SDK\examples\zigbee\experimental\cli...
Hello Sir
Sir i am try to sending the some text to nrf 52840 board,if you have any document please send it.
and how to do this process ? Sir please explain
Hi ;
If there is a ble message coming , but this time ble is getting data from sensor , what will happen ? Will it device reset ? Would you give me any idea to avoid this...
Dear all,
We have a question.
Did any body tried to make so that Bluetooth Mesh 4.2 works in PARALLEL with Bluetooth 5.
Some schedule reserved for BLE MESH 4.2 and some...
