But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello, Dear Support!
I explore examples in SDK 15.3.0 : ble_app_hrs and ble_app_rscs. The peripheral device in ble_app_rscs is configured to wait active request from central...
Hi,
I use the calendar to display on the screen the actual date. It works but now I want to display it only when I press a button, but the button doesn't work. When I press...
Hello everyone,
I'm using the nrf52840 Dev Kit (PCA10056 1.1.0 2019.19 683465548)
SDK version: 15.3
OS: Fedora
I work on a custom board and try to put it in SYSTEM...
Hi,
We are using nRF51822 chip, and we are using TL3315 switches. I am very new to dealing with buttons. The current problem is that when I press the button, the MCU seems...
Hi,
I would like to flash a CC3100MOD wifi chip from TI with the Nordic 52832 chip as a host. Attached is my schematic. I am fairly new to the nordic family but I have...
Hi,
The problem statement mentioned below.
What we are trying to do is Read Light value from the MAX44009 sensor on the TWI interface.
Looking at the data sheet for...
Hi,
I am using Nordic nRF52840 SoC with nRF5_SDK_15.2.0_9412b96 (SDK) and S140 softdevice. I tried to set Tx power to +8dbm using
rc = sd_ble_gap_tx_power_set (BLE_GAP_TX_POWER_ROLE_ADV...
I am currently involved in developing a product that is using the nrf52840. The product needs to keep precise time across a wide range of temperatures, which is why a 32Mhz...
Hi,
When I try spi commnucation with sensor on nrf52840 (using Mbed OS with SDK14.2), it stuck to nrf_spim_task_trigger (p_spim, NRF_SPIM_TASK_START); while spim_xfer is...
Hi,
I am trying to increase the sampling rate of the motion sensor on a Thingy:52. I managed to update the firmware and increase the BLE_GAP_ADV_INTERVAL_MAX from 200 to...
I am using softdevice s132, nRF52832 and SDK 15.3
This happens every time I connect the RX line.
This is an application where I implement UART with the HRS application...
Hi,
I am interested to know how to make a mesh node (for example, a light server) compatible to perform a DFU.
I have gone through the DFU page and I noticed that the...
Hello.
I am about to receive the Uart service for the Nordic SDK Central and peripheral.
I Use nrf 52832.
In the peripheral example, we used 'ble_nus_data_send'...
Hi,
I am using nRF52840 Enineering C chip on a custom board using SDK v15.3.0 with SoftDevice v6.1.1
I have modified the Blinky Central code and the Blinky Peripheral...
Hi. After my nRF52832 peripheral connects to an android / iOS, I am trying to read the MTU size that has been negotiated with the following code;
current_mtu is being...
