After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Hello Nordic Support Team I am working with 3 nrf52 dk board my 2 nrf52 dk board working good but My one nrf52 dk boards not detect on my pc and not any jlink storage drive...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. Now I want to store some data in the flash of nRF52832 but I worry I will destory the bonding...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96. Now I want to store some data in the flash of nRF52832 but I worry I will destory the bonding...
Hi,
I have been trying implement this , which i successfully implemented two week earlier. But for some reason i am not able to implement this anymore. I tried last week...
In trying to debug I2C usage of BNO055 device, I've sprinkled NRF_LOG_INFO around in my code.
This is Very simple stuff, yet I am seeing erratic behavior of the logging...
Hi! I'm testing a mqtt publish example in nRF5 SDK v15.2.0 with nRF52832 DK(pca10040). It succeeded in connecting with raspberry's mqtt-broker with non-secure type. It works...
Hi,
I'm working with nRF52832DK board , nRF5_SDK_15.0.0 SDK and nRF5SDK_Mesh2.2.0 Mesh SDK . verified the light_switch example project,i wanted to create beacons mesh network...
Hi!
I use softdevice3.0.0 , SDK12.1.0, Keil IDE, PCA10040 Development board,
I am going to create a multilink_central_NUS project using the ble_app_multilink_central...
hello
i want to implement provisioner and client roles in the same board , how can i start initializing the models
i have implemented the same initialization of the client...
after implementing some changes on the client and server examples i could compile my algorithm for the client but in the server i still have some problems which i didn't find...
While migrating from SDK 12.2 to SDK 14.2 DFU fails while flashing application and the pages assigned get in the switch case of FDS_PAGE_UNDEFINED always ,thus jumping from...
Hi,
I am using the gpregret register to select the device mode on startup and it is working as expected.
But it is not working after adding dfu functionality. does the...
Hi,
I am facing the problem as shown in the image below for two PCA10040 and two PCA10028 boards. I read related posts but none of them helped!! I did not make any changes...
Hi Nordic,
I am trying to implement a 3D mouse application using mpu9250,nRF52832 and ble_app_hid_mouse application from 14.2 SDK on custom_board.I am able to connect to...
