Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi All,
I have an issue with bootloader, in this i am successfully transferred application but after that my application not started.
i am just upgrading the sdk from...
Greetings,
I'm having the same weird issue as this question, though I don't understand the answer to it https://devzone.nordicsemi.com/f/nordic-q-a/34447/app-gets-stuck...
Hi everyone,
I've a nRF52810 based device that I am working with the Android based nRF Connect app on a Poco F1 (Oreo 8.1.0). The app scans the device properly but connection...
I just got my new nRF52840 dongle and went through the procedures stated. But I tried programming the nrf blinky firmware and after that I'm not able to connect the dongle...
Hi,
I am relatively new to the Nordic family of chips and I am very impressed with the level of documentation and support available, so many thanks for that.
I am working...
I would like to use the nRF52840 Dongle for evaluating the platform for a custom product. I need to make use of I2C, SPI, BLE and maybe 802.15.4 raw packet access. I'm new...
Hi :
I find some problem about th .
First I connect the USB,then I copy a folder with 18 binary files to my 52840DK,then reconnect.and compare the folders in DK with the...
Today, I tried out the Ble Bootloader from the Sdk examples.
As a central client, I'd used the »nRF Loader App« on an iPhone and also »nRF Mcp« on an Android Tablet (I'd...
I am interfacing My acc/gyro sensor (ICM-20648) with nrf52832. I am using my custom board and successfully get the mac address of my custom board. Noe i need to ensure about...
I use two PCA10040 for nus experiment, S132, SDK14.1
sniffer capture packets found that no data can be captured after the master send CONNECT_REQ, I guess it is not because...
Hello,
I have a working application on nrf52832, running sdk version 15.0 and SD132 version 6.0.0. Now I would like to add dfu functionality. I followed the instructions...
I followed this :
Connect the nRF5 boards to the USB ports and decide which one you want to use as a client and which one as a provisioner by noting down their 9-digit Segger...
Hi all,
I want to verify nRF52840 SoC SPIS peripheral on PCA10056 DK using any compatible SPI master hosts. I use SDK v15.2.0 SPIS example.
I know that Nordic SPIS peripheral...
