i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Can the
sd_ble_opt_set
function be used to set a default channel map in the central role prior to any connection requests to advertising peripherals being...
Hello,
I am using nRF52840 with nRF5_SDK_15.0.0_a53641a.
I am looking at the QSPI example which I have slightly modified so that after the write of 256 bytes, it enters...
Hello I just got nrf52dk board, and have issues with dfu mode of MCU, after power on board is dead no any lights, no USB connection. After pushing reset and power on, MCU...
Hello,
I am implementing an application, where I want to connect three NUS peripherals to one NUS client. As a beginning point, I started with the supplied examples from...
I have ported the keyboard example code and integrated it with another set of services. However I don't see the device responding to an LL_ENC_REQ. I'm not sure what I can...
This probably falls under the category of BLE Basics, but I'm a bit slow and need some help. Here's my scenario:
I'm building a very simple BLE Peripheral that provides...
I'm currently using nrf8001 to send data to my phone. To save power from the peripheral device, I wanted to change the connection parameters.
I set the min and max connection...
Hi, I'm using nRF52832 with my external board.
I'm recently working ble uart example.
I control motions with tx message such as LED, motor and so on.
Now, I want to...
Hi,
I need to set a client back to the state, when its flash was erased and programed, so if I understand this correctly, the provisioning data has to be erased.
How could...
I've been developing on the PCA10028 development kit with print statements working fine (though at the moment it seems only SEGGER_RTT print statements are working and not...
Hello,
I am getting an error message while I was compiling the "ble_nfc_pairing_reference" example. How can I obtain this " micro_ecc_lib_nrf52.a" file ?
Fatal Error...
Hi,
I'm trying to edit the nfc message in software but after a while the nfc stops working.
What could I be doing wrong? This is my code, I change the value every second...
I have a project that I assume was originally set up with SES on Windows. I need to build it with MacOS but I get an error 'sdk_errors.h file not found.' I assume this is...
Hi，
I finally want to integrate BLE and 2.4G in nRF52810.
【1】I am studying Timeslot，i found some articles in DevZone.
There is a mention of micro-ESB ， so what is micro...
Hi, I am currently testing some BLE sample code (the proximity code and hrs code) with the nRF52840 PDK and I am trying to just simply interface the GPIO interrupt example...
