But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I'm trying to put the nRF52 into sleep by using the following code in a loop:
__WFE();
__SEV();
__WFE();
But I see current consumption at around 5mA still, and...
The Bluetooth Mesh Light Switch example shows how to work with keys for a Mesh Network.
But I have some questions about who generate the keys and what they are used for....
Greatings!
I am sending a packet with data in it from my custom board with nrf51822 to my android phone using cahnged ble_app_uart. The packet is being sent 8 times before...
I have the Thread Coap examples running on two nRF52840 dev kits (coap server + coap client). When I try to check the coap traffic with a sniffer + Wireshark, Wireshark can...
Hi! I am trying to control volume up/down, and for the future possibly a few other functions within the ID 3 tag of the HID descriptor.
I am using the ble hids mouse example...
I am working on nRF52840 Preview DK. I want to generate a square wave with accuracy of ON and OFF time = 1 microsecond using timer for driving stepper motor DRB8825.
I...
I'm experiencing the same issues as a previous poster that went unresolved: devzone.nordicsemi.com/.../
With 1 or 2 peripherals (sensors), the connection works fine. With...
I have Nordic nRF52832 mini beacon device. How can i change UUID, Major,Minor values from Android and iOS app. Is it possible to change the those values from app ? If yes...
Hello, I want to measure the impedence of PCB antenna designed for nRF52832 based board.
I have the following quires.
Is it required to isolate antenna from NRF52832...
Hi,
I'm developing a server model and a client model(Both example are modified in accordance with the example of light_switch). In the example of client, I use the API...
hello friends,
i need to control 4 LED brightness using PWM according to accelerometer values. how can i do that
i am using SDK11, nrf52832, KEIL MDK5
i going to...
Hello,
Am using Freertos with SDK 13.1 and SD 4.0.5 on custom board.
My question is about buttons,We have one button need to configured for BLE Button.
I have board_custom...
Does the PPK require a Dev Kit (nRF5x kits) or a Segger J-Link, or is there a way to use it to measure current without either component? The user guide only shows setups with...
I have nRF52840 preview DK and want to read advertisement packet using nRF connect android app. I have read that Samsung galaxy S8 has Bluetooth 5 support. Has anyone here...
I am working on nRF52840 Preview DK. I want to generate a square wave with accuracy of ON and OFF time = 1 microsecond using timer for driving stepper motor DRB8825.
I...
