Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I have a bluetooth service which I want to have to initialise a TWI transaction (using app_twi). I want to get the data back from the TWI transaction, but I can't figure quite...
What is the pitch and spacing of the connectors on the underside of the PCA10004 and PCA10005 modules please? Is there a diagram showing dimensions anywhere in the documentation...
@Michael Dietz
Hi Michael!
I am not sure what happened to my last question regarding the BLE example using Segger Embedded Studio. It is no longer visible in the post...
i am already use sdk10 and Eclipse gcc tool chain set-up.. but when i am programming on nrf51822. so, it's not work. also, it's working on nrf51422 QFACAB0(0x0071)..
GIVE...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have the ble_app_hrs example working well with DFU.
When I take main.c from the example code and put it into an RTX project, the DFU stops working.
Symptom: nrfToolbox...
Hi,
I have a python scipt that uses pynrfjprog to program some custom information into a board's flash to be used by my application (calibration parameters, serial number...
I managed to compile the ble_app_uart on windows 8.1 with cygwin. I had to remove all abspath on the makefile, as launchpad gcc is not compatible with cygdrive notation.
...
Hi, I use the NUS most of the time.
(SDK 7.2 & S110 7.1 with IAR 7.1)
As you know, HID keyboard or mouse bond with centrals (smart phones).
After bonding, when using...
nRFgo was unable to read attach to the boards I have with the QFAABB parts, but reported QFAABA parts correctly and programmed them. nRFgo was at 1.21.02.
I updated to...
Hi,
I'd like to retain a value in RAM after any type of reset, including a watchdog timeout, so that I can read it back in the bootloader immediately after a reset.
...
Hello,
I followed the tutorial to use Eclipse GCC and both examples (blinky without softdevice and HRS with S110) work fine, i.e. I can build and flash them.
Now I try...
Hi,
First of all I appreciate the way nordic has put tutorials on the website for the newbies.
I am working with putting custom services in my code, and its working...
Hi everybody!!!
I am working on ANCS on NRF-DK51 (nrf51-sdk-9.0.0) and I get the disconnected reason 0x002A same as this topic . They said that to overcome this problem...
