After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
Our customer Farho is using the nRF905 transceiver a long time ago in their heater systems.
Now they have a project where they need to establish the communication with...
Hi everyone ,
I am working on button and pwm function by using timer ,whenever i press the button for 3 sec and pwm pulse signal is getting generated followed by pressing...
Hi,
I want to evaluate communication between several NRF51 chips using ANT. I could just buy a bunch of NRF51 DK kits but that seems pretty expensive.
What is the best...
Hi. I have the following code which runs perfectly on several C IDEs ( including Eclipse, Dev-C++, Code:Blocks and on the Linux Terminal using gcc as well ). However, when...
Hi,
I am an iOS developer trying to implement the app for an nrf51822 chip-based device. I am trying to perform DFU of application type using the objective-C files from...
As title, im using nRF51822 as a ble uart.(ble_app_uart)
But it will sleep when No connect for some time.
how can i turn off the sleep mode?
I want it be a "always...
Hi, may I looked bad , but I can not find NTF52 documentation, datasheet, evaluation board schematic, pinout, price... nothing , except the file nrf52.h in which I found some...
The following SDK files have incorrect comments:
markrages@qountdown:~$ grep 'units of 0.625' -r /opt/nrf51sdk-11.0.0 | grep 300 | grep to\ 25\ ms
/opt/nrf51sdk-11.0.0...
I configured nrf to go to sleep after 5 minutes of inactivity and then wake up by external signal (by accelerometer interrupt if any movement detected). what struck me is...
Hi again,
I'm here with another HID problem. When I flash my chip with standard HID mouse example, OS discovers it with it's declared in code name, connects succesfully...
I have designed an custom application board based on nRF51822 SoC,
Now i wanted to do testing on RF front.
I found one Test guideline(RF_Performance_Test_Guidelines_v1_0...
Hello Everyone,
I am able to do this functionality by using NRF5DK
Using Android APP (MCP master control panel) am able to make beep sound in the NRF51DK by using...
Im working with a nRF51422 EK. So, there is an android application with 2 buttons. Each of them can Set a LED. It will be set as long as the button is pressed on the application...
SDK:10.0.0
Here is the error when I compile
..............\components\softdevice\common\softdevice_handler\softdevice_handler.h(40): error: #5: cannot open source input...
Hello,
I have a project which is currently using S110 SoftDevice v7.1.0 with nRF51 SDK v6.1.0. The hardware is nRF51822 xxAA revision 2. It will probably be upgraded eventually...
