I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hi
We are using the nRF52832 with the SoftDevice S132 V7.2.0. Recently, we had to enable the FPU whereby we have to re-evaluate the consequences of erratum 220.
According...
Hello,
This is a theoretical question rather than a problem:
Let's say I have 2 devices that need to communicate over standard BLE profile and every so often needs to...
I'm using SDK1.3 on a nRF52840 and running BLE on it. I'm using FreeRTOS under it and specifically non-preemptive scheduling. From time to time I do a scan using a filter...
After upgrading to NCS 2.7.0 I noticed the MX25R1635F (A very commonly used / well supported chip for zephyr) no longer enters deep power down. On further investigation, changes...
Hello,
I have several sketches from prototyping my project but It's occurred to me that the libraries used for some sensors are unique. I want to use the SDK connect examples...
we are facing an issue with our nRF5340-nrf7002 custom device where, after a reset, it takes approximately 3-5 seconds to enter the application. This delay seems to be occurring...
I am considering software that uses nRF52840, where one side will send advertisements and the other side will scan and obtain data from advertisements.
I am considering...
Hi,
I’m developing a BLE IoT product using the nRF52840 DK, where I need to send a payload of 60 bytes. In a previous response to one of my questions, I was advised to increase...
I have a requirement for PMIC which should include charging, sleep mode integration and should give simultaneously 2 outputs. One output should range from 3-5V the other one...
Hey
I have tried to enable and test coredump as shown in this example: https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-2-debugging/topic...
My production board doesn't support UART, but we have SEEGER JLINK using RTT to debug with. I'm using nRF5_SDK_17.0.2_d674dde\examples\dtm\direct_test_mode project.
If I...
Hello.
I am experimenting with the nRF52-DK board. The tool is segger studio on win x64. Bluetooth appears on the smartphone and disappears after a while. It is not connecting...
Hello,
On my custom board, I need to offload data from my NRF52840 chip via Bluetooth/BLE to my PC for processing. (Ideally using python to receive) Is this formally covered...
We're evaluating RSP with 1oT, and we managed to successfully swap the carrier using RSP with our nRF9160DK, running our standard application.
The nRF9161-DK, running the...
Hello,
i'm developing a custom board with nPM1300 + nrf5340. First things first, i purchased a nPM1300-EK to acquire the needed knowledge to make things working. Unfortunately...
