I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hi,
Sorry, i am new to MQTT so may be asking a stupid question, please bear with me.
I am trying to run the MQTT sample (nrf\samples\net\mqtt) and get the following output...
I have been trying to measure the PER between two nRF52840 DKs using BLE. To do so, I am using BLE Direct Test Mode to start a transmission on a 52840 DK and another development...
Hi Nordic Team, I'm using the nrf52833 controller with nrf Connect SDK v1.9.1. I wanted to enable the watchdog in MCUBOOT starting main.c file and disable it just after giving...
I am developing a BLE DF project using the nRF52833 DK, and I am currently confused about the antenna location on my DK. I have not found any markings like "ANT" or "TX" on...
i have two toolchains inside my ncs directory. i am trying to build my main program using west build and the west exe that i am using is the one from the right toolchain....
Hi,
I'm doing nrf52833's spi function.I want to use hardware slice selection instead of pulling the gpio pin, and the reference manual has the register IFTIMING.CSNDUR....
Our custom development board uses an nrf52840 chip together with attached sensors. The data from sensors are stored in sd card. For this purpose, the Zephyr fs library is...
Here is a stacktrace from a device I got using the nRF Connect mobile app on Android.
nRF Connect, 2024-05-11 Device Name (A4:XX:XX:XX:XX:7C) D 13:40:23.035 [Callback] Connection...
I'm trying to setup a I2S module by referring the I2S module given in the nrf5340-audio application. This is my audio_i2s.c file.
Now when I'm building this...
What should I change to run the hci_lpuart sample with UART asynchronous API instead of the using the interrupt driven one? I have already changed the source file on the sample...
I was able to run blinky successfully on my customized nrf5340 board, but it doesn't respond to writing matter related code, there is no output from the RTT, I refer to the...
Hello,
I am reaching out regarding some challenges I've encountered with SPI communication on the nRF7002DK when interfacing with the ETH Wiz Click | Mikroe module and a...
Hello,
I am a student and new programmer and got the Thingy:91 for a project at Uni. I went through the getting Started guides and now I am at the point, where I downloaded...
