After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I am trying to format an external flash chip with littlefs, but keep getting an MPU fault. I can erase the chip, but not mount or format. I have tried writing and reading...
I'd like my VS Code build configuration for my project to be included in version control.
It seems like this configuration is stored somewhere in the "build" directory that...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
Performing a DFU with an iPhone works in some configurations and fails in other. Android consistently works.
The failing version of iOS is:
iPhone 12 mini
iPhone 13...
I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
Hi,
I would like to know what are the prerequisites to get the ICCID of the sim card:
This is the code I use, nothing special. I can get the IMEI of the modem but not...
Hello,
In nRF5340 I use one RTC and it works. Here is my code:
1) in prj.conf:
CONFIG_NRFX_RTC=y CONFIG_NRFX_RTC0=y
2) in the code:
a) define: nrfx_rtc_t sti_period_rtc_0...
Good morning,
I am using the nRF9160 as an AT command modem running the SLM app. I aim to set eDRX and disable PSM (PSM doesn´t make sense in our project). According to...
Hi all,
My team and I are evaluating some BLE modules available on the market. One of them is the UBLOX BMD-340, which contains the nRF52840-QIAA SoC.
We are encountering...
Hello Nordic Engineer,
I have already implemented a Mesh network using iOS nRF Mesh, 5340 DK, and 52840 DK, with the mesh_light example.
The NUS I used before was able...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Hi all, need to establish a CIS connection to an already connected BLE device with security level > = 2 . However when the ACL connection has security level > = 2 and the...
Hello, We're developing a project on a custom board based on nRF52832 and noticed that P0.20 is high on powerup, even with no firmware. Is there a way to controll the pin...
In the nRF5340 Audio DK example located at C:\ncs\nrf\applications\nrf5340_audio , I want to add a third board and communicate with it from the master (gateway) to send commands...
How can I read the whole advertising packet when are packets larger than some specific size? This is the issue. I want to read this adv packet:
But I only get this on...
