Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi:
MCU: nRF52832
The device is powered by a battery. When the battery voltage drops to around 1.3V but is not completely depleted, if the device is charged at this time...
I am in the development phase of a Bluetooth based system design, which will be able to receive audio stream from any mobile device and play on the speaker, and also it would...
Hi,
I'd like to provision my Thingy91x for use with my nRF Cloud (so I can use location services). How do I provision the Thingy91x for use with my own nRF Cloud? What should...
Hi.
I read on the download site of the nrf command line tools that they are being deprecated.
I want to be sure that i'm correct here: 1. nrfjprog is replaced by nrfutil...
I have an application that runs on nrf9160 and uses nrf52811 for Bluetooth with client-host setup. Problem is it sometimes crashes on startup going into endless reboot loop...
Hi, I recently purchased an nRF52833DK and tested the attached code. When using Gazell, the maximum throughput I achieved was around 85,333 bps. However, according to the...
How to reproduce the issue:
We have used the standard hello_world sample application in the zephyr repository. CONFIG_I2C, CONFIG_SHELL and CONFIG_I2C_SHELL configurations...
Hi, I run this sample https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bluetooth/mesh/dfu/distributor on two NRF52840DK, but I cpouldn't do the update, here is the...
I know that Zephyr supports its own test framework ZTest, but I have used CppUTest extensively on past projects.
I'm also using Quantum Leaps QP (for which there is a Zephyr...
Could I know how to enable openthread log in bulb project?
I have added some logs in modules/lib/openthread, but it can't be displayed in tool, how can I fix it？
BR
...
Hello.
I am trying DFU with reference to DevAcademy Lesson 9 . I am glad to see that it has been updated for v2.7.0 - v2.9.0. I am interested in the following settings....
I am working on nRF54L15 with ncs v2.9.0 and I have migrated the pwm code which was working well with nrf52840 but with nrf54l15 it is not working. I tried to debug the issue...
I am developing AoA for nRF52833.
Please tell me about antenna switching.
Setting:
PSEL.DFEGPIO[0]=28 PSEL.DFEGPIO[1]=29 PSEL.DFEGPIO[2]=30 PSEL.DFEGPIO[3]=31
SWITCHPATTERN...
