Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
I have a two fold question, to build a prototype, I would like to know how to get
tflite micro in zephyr build for nRF9151 DK?
Non-Terrestrial Networks (NTN) on above...
I have been using the nRF Connect for Desktop with the Programmer application for several years to attach our end device to the Dev Kit to program our device with no issues...
Hi
Can the device(nrf52832) be used as a BLE Mesh Provisioner and Light Switch Client(such as Generic OnOff Client) at the same time?
I want to develop a device (nrf52832...
Thanks in advanced. Based on nRF5_SDK_17.0.2, I can use i2c with icm42670p normally. Due to power consideration, I need to r/w this imu with spi either to decide which is...
Hi,
I'm developing with nRF Connect SDK v2.9.0 in VS Code. I followed the exercise l1_e1 from the intermediate course. When I debug with breakpoints and the first breakpoint...
Hello there,
I reported this issue in another thread under a different symptom. With more and more testing, it shows it is somehow related to both Android and the 54L15...
Hello.
I need to read IMU data from LIS2DH12 of nrf 52833 which is in DWM3001CDK. But nothing I do initializes sensor... i always receive
<err> lis2dh: Failed to read...
Hello!
I am learning to obtain data by SPI protocol from ICM20948 sensor using nRF54l15. I tried to write my code based on sample given on devacademy nRF Connect SDK Intermediate...
We are developing with the nRF9131EK. But there is no documentation of this board.
https://docs.nordicsemi.com/category/nrf-91-series
Can You add the information like...
Before developing our custom board, we connected our MCU to the DK via pins 26, 27 and after disabling VCOM0 via the DK configurator, we were able to communicate using AT...
Hello,
I wanted to know if the "direct test mode sample" could be used for the EVK-ANNA-B402C that integrates the nRF52833 in its SIP.
Because building with the board...
I have a nrf52840dongle and a nrf54l15 custom board. And I flashed bt hci_usb demo into nrf52840dongle, uart_peripheral demo into nrf54l15 board.
Now I want to use my nrf52840dongle...
I am performing a BLE DFU update on an nRF52840 using the nRF Connect Android app (v4.29.1) . The app successfully uploads the DFU package and reports that the update is completed...
Hello, Nordic team.
We started to fight with the nrf52-ble-image-transfer-demo repo (congratulations on the project, ovrebekk ).
We are using the nRF52840 DK (PCA10056...
How to control the Power (change from 8 dBm to -40dBm) we can relate and keep this delta as reference and check the rest of the current?
How to set the Standby and Sleep...
