Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I'm trying to update MCUboot from the application. As a first test, I enabled the flash shell commands. I can erase somewhere within the flash without problems:
uart:~$...
Hi,
I have a simple SPI circuit to read data from a flash memory W25Q64 to be exact and I have difficult time reading the device address of the chip through SPI.
The situation...
Hi Devzone,
we are working on nrf5340 mcu, from the DTM sample, l learned that the application run on network core only, but my application scenario is combine the DTM with...
Hello,
I'm using the SAADC voltage conversion formula from the Nordic example as follows: 10 bits are used in the example.
By the way I want to change ADC resolution...
This is a follow-up to my previous post . I'm developing a BLE Peripheral application on the nRF52832 that uses NRF_SDH_DISPATCH_MODEL_APPSH to receive events from the SoftDevice...
I think this is a bug report for the VScode plugin
One of my boards shows this error when I try to debug
Nrf52833 custom board connected with SWD on Jlink
I was...
Hey there ,
I am trying to modify the Nordic Radio Test example from the pack installer in Keil
for some reason I am getting "
Resource Not Found
We're sorry,...
hi team,
i am using nrf52840 controller and sdk 16.0 i want to know difference between twi and twim and twis driver apis in infocenter.which one i have to use once i connect...
I am trying to display the p_data received data using below inside NRF_BLE_SCAN_EVT_NOT_FOUND case but I am receiving the below data.
2| 1 |6|1a| ff |4c|0|2|15|ff|ff|0|0...
I am working on direction finding connectionless locator/beacon(AOD). We designed beacon board with nrf52811(build option is nrf52840 DK nrf52811) and antenna array, use a...
Hi Everyone,
I recently updated from SDK 1.8.0 to 2.2.0. With 1.8.0, I configured the nRF9160 MAGPIO and COEX0 in my Kconfig file. But with 2.2.0, I don't see that in the...
Hi,
In SDK2.0.0 version, can the TX_EN timing of nRF21540 be changed through SPI control?
If the timing of TX_EN can be changed through SPI control, how FW implements...
Hi,
The example that I use is from here .
I have to use the USB interface to send and receive data between the host PC and the nRF52840 chip.
In the example, I can only...
Hello all,
I'm using the sample for distance measurement nrf_dm. I'm using the ncs sdk 2.2.0, with toolchain 0.15.1. Currently the sample runs without any change, but now...
