Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
I want to set more features in a single service, but once there are more than four features, some features will fail and no error will be reported. Some features in the service...
Hi suport team
1、My ADC sampling circuit is shown in the figure below.
2、The actual voltage at ADC sampling is 1.37v, but the voltage measured by ADC is only 1.29v....
After programming the sample to my nRF9160 DK, I opened the terminal emulator and I observed the following messages:
1. HTTPS client sample started
2. Provisioning certificate...
I have tried the nus relay experimental example using nrf52dk and sdk 17. However it crashes when I try to connect using either nrfToolbox Uart or BlueFruit Connect (Uart...
Hello. I'm sorry for my bad English. I'm currently working on a development using nRF52840 based on ble_app_blinky, which is an example of s140 and peripheral. So, I want...
2. In the nRF sniffer software, the device I'm interested in does not show up in the "Source" column with its addess, b8:80:4f:6b:b6:9e, but as "TexasIns_6b:b6:9e". It seems...
Hello,
I'm finding problem to generate the library uECC.a to use in project secure_bootloader for nRF52833 (SDK17) using SEGGER.
I started from project SDK_17\examples...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
We find a Beaocn from other distributor , it got very less fluctuations. RSSI table show below.
Test method: 10 RSSI were collected from a hand-held mobile phone at...
Typically the Base address registers and Prefix registers are used to configure up to 8 logical addresses and then RXADDRESSES is used to filter which of the 8 logical address...
Hi,
The new AT monitor have a hard-to-reproduce bug: the subscriber entry list alignment is not specified in the linker script. Since structs are always aligned, that means...
Hi,
im porting our nrf9160 application from SDK 1.3 to SDK V1.6.1. and facing error while accessing NVS device in SDK V1.6.1.
in SDK 1.3 i used "device_get_binding(DT_FLASH_DEV_NAME...
Hi,
I have have certain thread that I would like to be active during a ble connection. I can suspend it when not needed and resume when connected. But as long as the thread...
