Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
Hi,
How can I make the device generate random address periodically? I searched on the forum and found people mentioned BLE_GAP_ADDR_CYCLE_MODE_AUTO when call sd_ble_gap_address_set...
Hi.
I have a product that acts as a peripheral, and bonds with centrals that are typically smartphones. Normally the peripheral uses a whitelist to only connect to bonded...
So I noticed the program goes into a state where it's stuck on NRF_BREAKPOINT_COND , which happens after getting into the following writeToLogger () template function. If...
Hello,
I am evaluating NCS 1.5.99 zephyr's sample"periodic_adv"and"periodic_sync"with two nrf52833 DK. The sample "periodic_adv" runs normally on nrf52833 DK.But the sample...
Hello,
I've been trying to use Zigbee Endpoint Logger for the light_bulb and light_switch sample. But I can't make it work. I've been looking through the quetions on this...
Hello guys, i want to implement nrf5-calendar-example in nrf51822 with SDK 12.3.
This library can use RTC0/RTC1/RTC2. But i have only RTC0 and this RTC0 is for SD (am i...
hello,
if i want to connect to a peripheral device with strongest RSSI. I need to get the RSSI before connecting.
and i know i can get the RSSI from event of BLE_GAP_EVT_ADV_REPORT...
I'm trying to read the values from the DS1307 RTC through TWI. I've established a connection with the device but am not sure I'm using the nrf_drv_twi_rx() function correctly...
Hi,
I'm trying to run the peripheral heart rate service example on a custom board using the internal 32kHz RC oscillator. However, the code hangs when soft device is enabled...
I am writing my own UART driver and having trouble getting subsequent interrupts. The first time I see the interrupt occurs but nothing after.
According to the product spec...
Hello
I'm using nRF910 DK and need to transmit to aws iot core just like the sample aws iot does, but instead of battery voltage I need to transmit gps data.
In sample...
I am seeing very little information. The LTE button lights green but Modem and UICC stay red. I get signal strength but none of the other items in the block; they are all...
I m using The nRF52840 + STM32 with serialization library. My device is set in central mode and i want to active whitelist,
the configuration seems to be applied correctly...
Dear support,
Anomaly 89 of the NRF52832 states that a high static current consumption is observed when the SPIM/TWIM uses EasyDMA and the GPIOTE is configured in event...
