I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi!
In our current project, we have started to use the Connect SDK.
We have a an application CPU with a modem running our main software and uses the nRF52833 for local...
Hi, I am trying to achieve the lowest current consumption possible on the nRF9160-DK, which should be about 1.4 uA in modem shut down state. Unfortunately, my best result...
Hi all, I want to form a thread network.
I have BorderRouter [Raspberry pi 3B flashed with Nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design] and is up and running...
Hello.
This issue was tested with nRF5 SDK v17.0.2.
There are steps to reproduce :
sdk_config.h should not be included in nrfx_clock.h. It's a default template by...
Hello,
I am looking for some help solving a peculiar issue with eddystone beacons, the nRF52805, and some cheaper Samsung android phones.
System Description: - I am using...
Hello,
I have been running this program without any problem then I added some code to read and write to flash using NVS when the error shown below appeared.
I am running...
I have been using the Toolbox to load zip files to a device. Now the toolbox uploads a file and 'say it is complete', but the file status in the menu window say file not loaded...
Hi forum,
I am working on nrf52832,using sdk15.0.0.
I referred TWI_sensor example as reference for sesnor interfacing. Individual sensor works when i trired to integrate...
Hi,
I am using an NRF 51422 DK, SDK 12.3, and Soft Device S130. I am also a beginner to development with Nordic Products, and RSSI collection in general. I am using the...
Hi Nordic team, I'm working with nRF52840 PCA10056 , base on Thread_Zigbee_ v4.1.0 , and light_control example. I modifed, try to add temp_measurement ZCL in all light_bulb...
Hi ,
My environment:
nrf5340 dk board
nrf connect sdk
segger studio IDE
.
I want to test spi loop back without any connections.
I don't want to connect any...
Hello, zephyr pwm driver documentation and samples , shows clearly how to generate a PWM output using nrf52840 dk. However, we need to synchronize the PWM output to an input...
Hello, how can we configure the counter in an nrfx52840 dev board to count pulses on an input pin in zephyr? There is a counter driver in zephyr, but there doesn't seem to...
What I'm trying to do, is probably very simple. I hope.
In the following code which works fine.
I want to scan not using Coded PHY
Then change back to using Coded PHY...
