Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
this works well with an Apple 11-13, but on 14+ Apple has removed the second antenna from the phone, so it cannot do ranging natively.
the AR approach does not work for...
I don't know why sample code is not easily compiled.
I have to add many feature such as CONFIG_SERIAL=y on prj.conf
This is not a sample.....
Anyway,
I cannot run...
Hi
I'm using the pawr_sync and pawr_adv samples as references in my project. I have implemented them so that the sync node scans for new syncs for n secs at a specified...
Hello,
I'm using an nRF52832 and an accelerometer/gyro to record data and send it over Bluetooth. My end goal is to store this data in large chunks, and then send it all...
With the recent release of SDK 2.8.0 enabling tracing with Segger Systemview locks up the system.
The offending issue is buf = net_buf_alloc(&hci_cmd_pool, K_FOREVER); which...
Hi,
My customer asked about using nRF Cloud for device firmware updates and maybe more, and I'm trying to figure out if this is possible and how difficult it would be to...
Hi there.
I'm currently working on driving a radio_test example using the 7002DK. I downloaded the radio_test example using nRF Connect and ran the bulid to drive it. The...
Existing FW developed on PCA10040 EVB, moved to EVM-BC805 which is the chip for my final board design. I applied the patch that I found to SDK 17. However this anomaly function...
I just bought a new laptop: IdeaPad 3 15IAU 7 running Windows 11 and I try to use it and the "nRF Connect for Desktop v5.1.0" and its "Quick Start" option to communicate via...
Can you please help us to convert following snippet from dts to mp_static.yml to use it for DFU applcation. We have external nand flash which used with littlefs and internal...
Hi all,
I have to measure the frequency of a PWM signal routed to one of the nRF52840 GPIO pins.
The signal frequency is ~3MHz.
The measurement is done with the help...
I am encountering the error message " <err> net_pkt: Uncontiguous data cannot be linearized " when already connected with nRF7002-DK to a Wi-Fi network using the EAP-TLS authentication...
I'm following the nordic academic courses, which are very nice by the way!
I've now followed three topics and I find three different variants which confuse me a lot: ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
Hello,
is it possible to read UICR at address FF8000 from a non secure application for nrf(160.
If yes, can you provide sample code and CONFIG to enable in prj.conf. ...