I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
Hello,
Would appreciate some understanding of a compiler warning. Developing for nRF52832 using SDK 15.3.0 plus S112.
This code compiles without warning:
Then I switch...
I have tried a lot of different settings but the NRF52810 still does not output carrier..
How do I configure the radio to only send carrier for NRF52810?
Hi,
I need to stream data from NUS UART Central Device to one peripheral, but the device always disconnects while trying to send second set of data. So I changed the write_req...
Dear
I have changed light_switch server example of " nrf5_SDK_for_Mesh_v4.0.0_src" from PCA10056 to PCA10059. All function of the code works well except button.
For button...
Morning. I have a Fanstel840F module. I use attached example sketch. I flash nrf52DK with this sketch, it works fine. I can scan with NRF PC and Mobile software, and see smartTag1003...
Hi,
May i know any software utility suggestion to debug the USB data (200 bytes data) communication from device to host and vice versa for nRF52840.
Similar USB sniffer...
I think there is a bug in the west tool. If only one -Dxxxx=”xx.h" parameter in the command-line, the quotes will be filtered. So update the "nrfxlib\nrf_security\src\mbedtls...
Hello, everyone!
I am using nRF52DK and SDK v17, and I am dealing with the example of ble_app_uart.
Using this example, I am testing how buttons control BLE scanning...
Hello. I am trying to implement a application jump from my normal firmware located at memory 0x19000 per recommendations based on the soft device used (s112) to a different...
Hello,
I am working on the nrf9160 board using cloud client sample. The connection to AWS and the boards loses after running for a while. When I reset the board it connects...
Hi,
I'm super rookie on BLE project,
my question is how can I using button press to accept a central pairing instead of typing passkey,
here's my code, using nrf 52810...
Hello!
We are trying to send MQTT messages to a hosted mosquito broker via AT commands using the nRF9160.
We are trying to avoid programming the nrf9160 chip, as we...
SAADC resolution is set to 8 bits, channel is configured as single ended. Is it correct to say that SAADC digital output should be between 0x0000 and 0x00FF(full scale)? ...
Hi,
I'm testing the ble_app_uart example on the nRF52840 DK and it seems to be consuming a lot of current similar to the case in https://devzone.nordicsemi.com/f/nordic...
In a single core BLE SOC, whenever a BLE event occurs the BLE stack takes high priority and any application code running on the single core, is delayed while the event is...
