Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I have some question about nRF52832 Bluetooth Firmware upgrade problem:
1. I have a device with nRF52832 in my hand. If I don't use the JTag interface, how can I confirm...
Hi,
We are using Nrf51 with SDK nRF5_SDK_12.3.0_d7731ad
We based a UART bridge on the BLE_APP_UART example
The UART connectivity is Rx/ x only (RX_PIN_NUMBER 0; TX_PIN_NUMBER...
Hi,
we've noticed that after performing an OTA DFU, the Bluetooth Address of the device changes as follows: new_address = old_address - 1
Example: Address before OTA DFU...
Hi there,
I am a beginner to the nRF series and I had the following question.
For a battery powered system, is it better to run the nRF52840 at a lower voltage such...
Hello,
i'm trying to program on 51422. The BLE signal,which runs well on 51DK, doesn't trigger any signal on my own PCB. i've successfully light the LED on my PCB. i think...
Hi,
I'm using nRF52832 and I'm trying to switch from SDK15.0 to SDK 15.2. While I've been able to install micro-ecc library in SDK15.0 and use OTA DFU, somehow I'm stuck...
Hello.
I want to integrate UART and SPI ,I am using SDK15.2. The problem here is i am not able to add app_uart.h to main.c(spi).
My question here is how to add it to main...
My working platform is nRF52-DK, and I want to execute DFU firmware upgrade
1. How to create a Bootloader Image? Which Source-Code of SDK_15_2 is used to build the bootloader...
The RTC documentation states that the LFCLK source needs to be explicitly started by the software.
Is this step necessary when using the SoftDevice? As far as I know, the...
I'm not sure about how does the ble_app_att_mtu_throuthput example works exactly, i supose the throughput test runs as follows:
1 tester defines a service 'populated' with...
Dear all ,
Working with nRF52832 (currently without SoftDevice), and there some issues regarding the project current consumption that we need to understand:
1) In the...
Hi,
I am having a trouble trying to make a custom service from SDK 15.0 ble peripheral template example. I have followed the tutorial from : https://devzone.nordicsemi.com...
Hi i'm a newbie, Got Thingy:52 (Keil and J-link) and want to develop HOGP keyboard application. Where can I find Tutorial or example ?
Is there a step by step guide on how...
