Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi there,
I am trying to use UART on the nRF52840 on a custom PCB. The custom board is connected to the nRF52840-DK with a debug connector. Am I free to set any pins on...
I want to create a router that only communicates with Bluetooth, not the gateway that connects to other networks.
The configuration is as follows.
C oordinator + Router...
Greetings,
I'm having troubles getting the Mesh lighting demo to work. Here are the details:
IDE = SES 4.12
SDK = nRF5 SDK v15.2.0, nRF5 Mesh SDK v3.1.0
SoftDevice...
Hi, Is there a usb hidapi sample code for nrf52840 somewhere? I know that there is a sample code of usbd_cdc_acm. Using the HIDAPI library link below , It will be beneficial...
Hi,
I am working on a Bluetooth Mesh project in which I am trying to add support for NFC, but I get the following error " error: multiple definition of `SWI2_EGU2_IRQHandler...
I'm new to nRF9160. I have some experience of implementing stm32 MCU and HL8548(3G module).
I want to send at commands to outside module like Wifi module, and receive return...
I have Nordic NRF 52840 DK development board, using Ubuntu 18.04, I loaded "ble_connectivity_s140_usb_hci_pca10056" to the board successfully. Then I powered cycle and cannot...
My setup: Eclipse, nrf52832 on a custom target board, s132, SDK13
I am trying to implement the workaround for the problem described here:
https://devzone.nordicsemi.com...
Hi everybody,
I would like to know how the module nRF9160 comes from the factory in it default configuration.
Is it possible to use it in UART mode only with the pin 86...
