i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
I want to extend the Thread Cloud Client Example (thread_cloud_coap_client_pca10056) with a peripheral controller. And I am looking at the UART Example (ble_app_uart_pca10056_s140...
Hi,
I will connect nRF52840 with other BLE module (ESP32) and they must exchange data (at first aproximation 20-50 bytes each 1-5 seconds).
I need to acheive lowest power...
nRF52 DK,software is nRF5_SDK_12.3.0_d7731ad,I'm using the example of "ble_app_multilink_central". SoftDevice is "s132_nrf52_3.0.0_softdevice.hex"
The BLE device is advertising...
Hi,
There is a racing issue in file: nRF5_SDK_for_Thread_and_Zigbee/components/iot/background_dfu/transport/coap/coap_dfu.c in function:
Sometimes calculated dalay is...
I'm trying to merge uart example in nrf5 sdk with light switch server example in mesh sdk
but I'm only facing these 2 errors :
when Linking uart_pca10040.elf:
Output...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I just wanted to know that What is the wake up procedure of the MCU when we call the sleep...
Hi,
I have a trouble trying to start development process on my NRF52840 DK.
Following the instructions
https://www.nordicsemi.com/eng/Products/Getting-started-with-the...
The nRF Connect application can not search the device after I modified the Rx, Tx pin in my own PCB board.Can anyone tell me why?
The UART can run well,but the application...
Dear Sir/Madam,
I tried to add battery service to the sample "ble_app_uart", but the code doesn't send notifications to cell phone. I struggled for several days and try...
Upon my first connection to my device with LE Privacy, first connection meaning after I've reset the firmware, I'm unable to read anything. The write characteristic works...
I am trying to use a Raspberry Pi as a provisioner for nRF52 development kits. I can run the meshctl utility on Pi but I am not able to see the un-provisioned beacons on the...
My application running on top of the S132 has a data base which can store up to 12 hours of data (720 points @6 bytes each). A request is made from the GATT Client to retrieve...
