Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Naive follow up to What is NUS? .
Is NUS merely a vehicle for tutorials and fast prototyping? Or can it be used to build real world apps on?
If so, do we rename the...
Hi All,
We are in design phase of our project . We would like to use NRF52832 for our project.
Our project is a wearable based on BLE. We are planning to use RTOS in NRF52...
I am starting to port the example
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_peripheral\ble_app_hrs to my board. I haven't made any change to the example to save something...
Hello, I have a problem when I attempted to increase timeslot length with 10 ms ,every time I received NRF_RADIO_CALLBACK_SIGNAL_TYPE_EXTEND_FAILED signal.
Why can't to extend...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE.
If the program is wrong,The chip will reset,
I want to save some data to the FLASH area before the chip reset.
What I need to...
nRF 8001: How to use it in Beacon mode where in no pairing or Bonding is required and
it only transmits some information which cn be received by any phone that comes in range...
Hi.I had been confused with parameters of sd_ble_gatts_characteristic_add( ).If I set parameters
like that:
static uint8_t ast_notify_char;
..........................
HI,
I have to implement buttonless bootloader.I am having simple doubt.I am programming softdevice,application(Hrs example with bootloader),bootloader hex file using nrfgostudio...
Hi,
I am trying to perform RF production testing using nRF51 development kit. My DUT is another nRF51 DK. I am setting my DUT according to Figure 2 mentioned in nAN 34...
HI,all
when i want to notify with MITM,there is an issue with my project.
my central role device is IPHONE and the app is lightblue .
When i enabel notify ,the nrf52382...
Hello,
I am using battery (3V) to supply nRF51822 system and the circuit is made according to DCDC mode circuit. My question is :
what is lowest voltage the battery can...
I have two p_storage_param modules param and param2 . param would store 3 blocks of 16 bytes and param2 would store 10240 bytes (10 pages). I called pstorage_register (param2...
Hello,
I followed both tutorials about using Eclipse GCC and migrating to peer manager.
I get no error when I follow them individually, i.e. when I use the project included...
Hi,
I developed an application based on s110 using the nrf51 DK and it works fine. The DK is based on a nrf51422 QFAC which is the biggest one in terms of memory sizes. Now...
Hi,
the mesh_dfu.c requires the definition of tx_config_t, which I can't find anywhere in the repo branch sdk-8-support. Same with RBC_MESH_EVENT_TYPE_DFU_SOURCE and other...
