When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi,nordic team，
im use nrf52840 develop my product with sdk ncs 2.6.the speed of desktop dfu is so slow,and the speed of configurator channel is also slow.i want to transfer...
Hello. I am facing an issue in configuring ADC for multichannels. I was looking at the Nordic fundamentals course Lesson 6 Exercise 2 .In this example, the adc is configured...
I was working through Nordic Intermediate course lesson 8 exercise 2 - DFU over USB, adding external flash and custom keys. I was using an nRF5280DK. (Sticker: PCA10056 2...
I have been trying to implement a DFU OTA using Bluetooth Low Energy from one nRF52840 DK to another nRF52840 DK using the smp_client_ble ( https://github.com/hellesvik-nordic...
hello.
I am using nRF52820 and nRF5 SDK (17.1.0).
When the fds_gc() function is executed, all bonding information in the pairing area (flash) is erased.
My understanding...
I'm using CYCCNT to time code. Works fine until APPROTECT is set, then after reboot the CYCCNT is always 0. Is there a way to enable CYCCNT when APPROTECT is set?
I'm using...
Hi everyone!
Setup:
Currently, I am using the nRF52840 DK board to evaluate neural network models directly on the nRF microcontroller. To measure the power consumption...
Hi!
I'm using an external flash (SPI NOR) to store the secondary partition slot of MCUboot. According to datasheet, the SPI NOR chip in use supports 4KB, 32KB and 64KB paging...
I am having a problem to get the board to do DFU without entering the bootloader mode. Furthermore, when the board entered bootloader mode, it showed only a single slot with...
Hi, In our custom board, currently we using SWD with segger J-link for DFU Is there any another option except segger/dev-kit ? Can we do DFU through USB/UART ?
I am trying to setup visual studio code with nrfConnect extension on MacOS 14.6.1 running on apple silicon.- After installing the extensions, I am not seeing the welcome menu...
Hello! I'm trying to connect to a peripheral Bluetooth device with the device information service using version 15.3 of the nRF5 SDK and a nrf52832. When I connect to the...
