Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
We are using the nordic sdk 1.9.1.
I have created my own project and i want whole sdk commit to my repo. I am able to build the project. I am not able to commit the...
Hello Guys,
I am trying to implement our own firmware update over ble in Mobile App.
The whole process is succesfully done by Nordic Application (Device Manager).
I...
Hi,
I'm implementing a circuit that uses both ble and usb communication using nRF52840.
I'm configuring power source and i'll configure schematic like reference circuit...
Hi there.
I am currently developing a simple asset tracker based on several examples using nrf9160 custom board.
So I am using several examples like mqtt_simple, gnss...
Hi,
I am using STLED524 intelligent matrix LED display driver IC for my project.I need to interface STLED524 with nRF 52 board.I am checking for driver library for it.But...
Dear All,
I'm implementing a SNTP sync over Ethernet and found the following issues:
1- CONFIG_DATE_TIME_AUTO_UPDATE must be disabled to get a NTP time sync scheduling...
It seems like there are lots of questions regarding simple GPIOs and devicetree, but I can't quite find something that describes my problem:
I am using the nrf52840dk...
Hi,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the reference...
I have developed a thread network using nRF52840 dongle and Raspberry Pi 4B. I have checked from the command line of the RPi, the transmit power is 0dBm. Can you please confirm...
Hi,
I use embedded wizard tool to handle display graphic and I need allocate a RAM buffer for it. I need to write frame buffer ram start and size in embedded wizard config...
Hi all,
I want to compile chip-tool so that I can make 5340 into a matter network. But I always fail to compile.
environment:
raspberry pi 4B + ubuntu-22.04.1-preinstalled...
Hello,
I am trying to load an application update from a server into external flash, the download itself is working but mcuboot is not:
I need to use the external flash...
Happy holidays!
I'm trying to generate .bin files for examples like direction_finding_connectionless_tx and direction_finding_connectionless_rx but i can't do it, can you...
Hi, I've experienced an error in which a peripheral connects but can not send any data. I have these logs: [1672131059] <err> bt_ctlr_hci: Tx Buffer Overflow [1672131059]...
Hi nRF community,
I have a question regarding the lowest power consumption ever possible with nRF52832 chip.
I'm experimenting with power consumption using nRF52832...
