When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Good day
I am attempting to use lwm2m to post temperature sensor data. At the moment I'm trying to to initialize object with ID 3300 (generic sensor)but it is not appearing...
MacOSX 13.0.1, Intel. nRF Connect SDK v2.2.0 as downloaded by Toolchain Manager v1.2.1 from nRF Connect for Desktop 3.12.1.
Same happened with SDK v2.1.2.
Similar steps...
Hi,
I was trying to put the nRF5340 Audio DK board in DTM mode to test RF capability but couldn't find out any way to do so.
Please let me know if I can find some documentation...
Hi,
We have 3 nrf5340 Audio DKs we want to connect together. One of the devices is connected as central and the two others are connected as peripheal. By know, the two peripheal...
Hi!
We plan to build an AoA localization system with the nRF52833. To calculate the signal phases per channel, the antennas are connected to the BLE-RX via switches sequentially...
I am working on the nfc uart examples. first I found the poller example is not support for 10056 board. I make the change for that. code can build and flashed, but then I...
Hello,
My development requires new device binding and I want to share the steps followed and my issue.
My device is Renesas and commuicate via I2C protocol.
Based on...
Hi Team,
I am using nrf52840 controller and SDK 16.0. I have referred to the product specification manual/data sheet already. However, I would like to have the " programmer...
Hi,
We received the new nRF52840 USB dongles this week, however when we try to access the getting started URL on the dongle package the web page gives an error.
The...
Hi
I am creating a simple firmware based on BLE Peripheral UART for nrf5340 (currently using DK). Before, I able to create notification to user app (I am currently using...
Hi,
I get some question about the nrf52833 nfc digital modulation signal feature. I think the biggest changes is allow to using external frontend. I just want to check if...
I use VSCode as my primary development environment for several different client project. I recently have been evaluating the nRF Connect extension for VSCOde. I do not want...
Dear Nordic Engineers
I test the ble_app_bms program and I have a problem would like to ask you.
I download nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_bms...
Hi Everyone,
I am using nrf52840 in my project which is used as a central device. I have my app through which I can send data to the central device. The device is also able...
