I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hi, we are currently trying to reduce the power consumption on our product that uses an nrf52810.
An 1k pull-down resistor has been used on the SWDIO pin, but I don't really...
Hi,
I am using nRF52833 & nCS for an application development,
I am facing a curious issue where, if i enable printk in nCS build, I am getting SUCCESS on calling device_get_binding...
I'm trying to join two programs that work well by themselves, a saadc program that shows the force sensor value in the serial, and a BLE program that turn on or off a LED...
Hello every body,
I'm now utilizing the nRF9160 to develop several products based on SDK 2.0.0. In my program, I must produce SBOM.
This link below has some information...
I am on project using nRF52832 WLCSP.
What's the pin assignment for SWDIO pin? I want to read the input of SWDIO (as indicated in datasheet it's Digital I/O) and can it...
Dear Concern,
We were developing one of our products using nrf52840. We previously used the nrf-52840 USB dongle for the product. Now we were moving to nrf52840 chip based...
Hi,
nRF5340 + nRF21540, NCS2.0.2, VScode
i follow Working with RF front-end modules — nRF Connect SDK 2.0.99 documentation (nordicsemi.com)
how to disable TX_EN? i only...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
Dear Mate,
I am using bl653_dvk board i followed this link clearly (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi...
