I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi,
as am following below link for DFU-OTA . i was able to perform it. https://devzone.nordicsemi.com/f/nordic-q-a/83402/ncs1-8-0-52840-mcuboot-spi-external-flash-can-t...
Hello, this is a follow up on this ticket: https://devzone.nordicsemi.com/f/nordic-q-a/84834/protecting-the-battery-via-sleep-mode
Our goal is to switch off the device ...
Hi,
I'm trying to understand which of the BT L2CAP modes are supported for a BT LE Controller. BT Core 5.3 supports these modes of operation:
Basic L2CAP Mode
Flow...
Hi.
Is it possible to add SPI or QSPI cleanup once mcuboot is done?
I've checked nrf_cleanup.c , but it seems that (Q)SPI is not turned off, which increases the power...
Hello,
I'm using nRF52833 MCU board for my project, I have to do power optimization to my project(Device).
In my device two sensors are there, and boost regulator and...
Hi, I have made a project that is based upon the aws_iot sample. The version of SDK and toolchain is 1.7.1. Now I have tried to upgrade to version 1.9.1. But then I get compile...
I've written a sample eeprom application based on the eeprom included in the nRF52 SDK to test the EEPROM we use in a project. The application worked properly about 10 days...
Hello! We created our own model using SDK for Mesh and it works well. However, when testing in the "nRF Mesh" application using the "Vendor Model Control" field with the ...
When i use GPIOTE HITOLO(low accuracy）and then open spi to read flash and close the SPI（nrf_drv_spi_uninit） and close the SPI 's GPIO (nrf_gpio_cfg_default) .
The power...
Hello,
How do I create an encrypted/signed image? Where can I find the documentation for doing this? How will I need to modify the bootloader to decode and install the image...
Hi, I need some help on flashing the code to nRF52832 BLE module. I would like to mention that I am flashing the code to nRF module using ST-link v2 debugger with the help...
Hi,
I've encountered problem with app timer functions being called from different interrupt levels. Looks like no memory error returned is caused by collision in underlaying...
Dear Nordic,
I'm trying to determine why my nRF9160 cannot register on the Verizon network. Does Nordic have any tools which allow one to see the RRC messages between the...
I just try to connect to J2 port like I always used. I tested several cables and several USB ports, I'm using MAC os. 1. Power switch is ON
2. nRF Power source switch is...
Hi ,
We are building a ble mesh related project with nrf52840 soc with NRF MESH SDK 5 . After certain amount of development work we are facing issues related to synchronization...
