Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
We need to read/write to an I2C device that uses a 16-bit register addresses (Melexis MLX90632), and the nrf_drv_twi_tx() and nrf_drv_twi_rf() functions seem to be limited...
Hi,
We would like to impelement Pairing and security features in our device. Our device will act as server in peripheral mode. The cleint device should ask for 1 passkey...
Hi Nordic,
I'm referring to this doc but still not quite clear about how to enable the chip for BLE RF HW validation.
infocenter.nordicsemi.com/index.jsp
What would...
Hi,
I have modify the payload of the Light Switch example of the NRF MESH SDK. When I send 50 bytes or less, all works fines : the server nodes received all the bytes...
Hi everyone,
I am developping on a custom board using nRF52840, using MCUboot v1.8.99-ncs1 and nRF Connect sdk v1.8.
For development matters, I would like to change the...
Hi, I want to include the pairing and bonding features in my application.
I want to use the LE secure connection method. For both initiator and responded the IO capabilities...
I adding custom pins declarations through overlay file as in first image with corresponding yaml file ( see attachment) with path .. /dts/bindings/gpio/custom.yaml. The project...
Good Day. I am wondering if anyone could maybe assist me in where I am going wrong with my software.
I have the intention of using a Nrf9160 as a serial modem through AT...
I use nrf9160 to develop a product for customers. The modem is also set to PSM and the log is turned off. However, I find that when the modem is connected to the Internet...
When I try to connect to nrf52840 using J-Link, the following error is detected.
What is the reason for this "Failed to power up DAP"?
- Connecting via USB to probe/ programmer...
Hello nordic support:
We want to measure nRF9160's LTE RX SNR at production stage .
According to the document nwp_034--nRF9160 Hardware.pdf ==> 4.6.1. Following command...
Hi, I am working on nRF52832 as central. When I program it to form Segger Embedded Studio it's working fine but when I upload that .hex file from the nRF Connect device did...
Hi there,
We are designing a coin cell (3 V nominal) battery powered product; we'd like the ability to run it all the way down to 2.0 V for maximum lifetime. To get the...
