I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
BT_DRV_RX_STACK_SIZE is too small and can't be configured. It needs to be more than 512 bytes in released versions of Zephyr, or 640 bytes, on the main branch. Note: I'm using...
Good morning everyone,
I am going crazy to solve this problem, but I hope we can figure it out with some help.
I am working on a prototype for which we need to use a...
The documentation for the Maximum Performance sample mysteriously states that the sample is not supported on the 5340 with no explanation as to why. As I am getting spurious...
Dear support,
I am using this board: https://www.nologo.tech/en/product/otherboard/NRF52840.html#%E5%BC%95%E8%84%9A%E5%9B%BE . I am trying to use any analog input to eventually...
nRF Connect for VS Code v2024.12.55 showed up yesterday and it seems to be broken for me; the "build", "flash", debug" buttons are not available to me, I am stuck with "Pristine...
Hello,
I fear that my toolchain and environment is seriously confused.
When i use the vs code extension sdk to install a toolchain or sdk i get the following message ...
I Have been trying to interface mpu6050 with nrf5340 DK .
f ( NOT "${ret}" STREQUAL "0" )
message (FATAL_ERROR "command failed with return code: ${ret}" )
endif (...
Hi,
I'd like to know what is the cause of the stall in
sym_E5Q6O4GY4KO3GMW7WJYXLZKHO7ZGDWLU4ZPAKWA() at 0xa55a
when calling sdc_hci_cmd_le_set_adv_enable ?
Here is...
I am currently considering the use of an external Flash IC for a Matter device.
I have two questions and would appreciate your help:
1. Is the MX25R6435FZNIL0, which is...
Hello,
according the datasheet the nRF52832 has an gain error of 0.02%/ ◦C and E_G1 of -3 ... +4%. This is too high for our requirements. Is there a way to improve this...
Hello DevZone,
I'm developing a HomeKit project for the customer. They require 2 BLE advertising in one device. One advertising is for HomeKit over BLE, and the other one...
i want to switch between two code... the code is simple led blinking i am trying for the testing purpose...in my code 1 led1 is blinking 500 ms of delay and in my code 2 led2...
So from my understanding from the zephyr documentation, if I want to use 7 bit I2C addressing, don't set I2C_ADDR_10_BITS. I am wondering how I can make sure this macro is...
Hi,
How do I add the System ID characteristic (UUID 0x2A23) from the Device Information Service (DIS) using Kconfig commands in the prj.conf file?
For example, I can add...
Hello,
I am having a strange problem with nRF Connect SDK for VS Code, and would appreciate some help.
I don't know what I did, but suddenly I am not able to "Generate...