I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hi,
I was able the configure the sample to connect to AWS but I cannot figure out where the cloud_send function is sending the data. Is there any documentation on where...
Hi all,
I am using a nRF52840-DK as SPI slave with a MSP430 as host SPI master for a nRF8001 replacement application.
As I am absolutely not familiar with high level functions...
I am trying to communicate with a SH1106 OLED display using TWI and the popular u8g2 display controller library.
I've verified that the display works without problems on...
I am currently development an app based on the example from the experimental folder using a NRF DK52 as a relay between a central and multiple peripherals.
The app should...
Hello,
Happy New Year.
I'm not able to find nRF52840-QIAA-T or any replacement of this SoC available in the North American market.
I need atleast 5 SoC of the...
Setup: nrf52840 (without internal dc/dc), VDD = 3.3V
Assuming the VDD rail ramps up slowly, the nrf52 will start booting at it's power-on reset threshold of 1.75V (POR)...
Dear BLE Experts, I've followed this tutorial to create a custom GATT service and characteristic. The tutorial seems to be based on the BLE SDK , not the MESH sdk, hence the...
Hello,
Our company is kicking off a project (while we are at the very beginning stage) where multiple nodes (up to 1K) should be connected within a mutual network. I wanted...
We are looking to increase battery life for a product that uses the nRF52832. I'm wondering if it's possible to provide 1.3V directly to the DEC4 pin rather than use the internal...
Hi, I'm referring to this post over 3 years ago: Nordic DevZone (nordicsemi.com)
I'm using Android 8.0, and I'm using SDK 12.3.0 for firmware. I'm trying to create bond...
Hi,
I noticed that when I initiate a chip-erase on the flash-chip and reset the MCU, I'm getting NRFX_ERROR_TIMEOUT's on my nrfx_qspi_init().
I found this ticket: https...
i am using nrf52840 DK with softdevice (s140_nrf52840_5.0.0-1.alpha_softdevice) and applying this throughput example ATT_MTU Throughput Example . and notice that when I use...
Hello I have a problem with the scanning of ble phy coded in Android, I need it to be continuous (or almost) but it seems that for coded it is not possible unlike with legacy...
There are more than one task, after completing the periodic work,the 52832 module should enter system on low power mode,sleep 30 minutes,then wake up and continue with the...
