i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I am trying to execute code that broadcasts (uses the Soft Device Ble stack) on target nrf52832 boards connected to the PCA10040.
I am successful uploading a program (that...
Environment
nRF52832, nRF5x-Command-Line-Tools_9_7_1_Linux-x86_64,
Problem:
Programming of Softdevice, Application and Bootloader with nRFGo Studio works.
Programming...
Hello,
As I understand it, bluetooth declaration IDs can be used for multiple products as long as the products all share the same QDID . In other words, If you do it right...
I have been following the tutorial devzone.nordicsemi.com/.../ on how to use eclipse but in the makefile part im getting this error. I'm using sdk v11. I have used sdk v14...
hi,
i doing a program to receive multiple service data from nrf thingy 52 to nrf52840 central device.
as of now i have implemented weather service, motion service and...
I have been trying to integrate support for multiperipherals into my application, but am continuing to get errors when attempting to start advertising after the first connection...
As I don't know much about audio,I have trouble with the gain of the pdm module in nrf52832.Now
I have used MP45DT02 as the digital microphone,but I just can't understand...
Hi, I've searched and googled through this site and made sure no one asked this question before.
In core\Bearer_event.c, there is this function:
bearer_event_flag_t...
I'm trying to connect two nRF5 devices together, Central and Peripheral, and use a custom BLE service that I have written that has a custom 128 bit UUID.
I'm in the process...
Hi,
We are sending a data using Nordic UART Service (NUS), the data is transferred over BLE as a Indication.
From Message Sequence Chart in Nordic Infocenter
Here...
I am researching OTA procedures and I spent more than a few minutes wrestling with flashing soft devices and bootloader code to the nRF52_DK.
What I found is JLINK seems...
When adding extra buttons on breadboard for NRF52-DK do we need to use resistors OR i can directly connect one leg to GPIO pin i.e 30 and another to gnd.
I'm trying to use the nRF24LU1P as a standalone 8051 with the nRF24 radio inside. I provide 5v on the USB connection but no host connection. I am trying to operate in PRX...
Hello,
I'm using the nRF52840 development kit with the "« ble_app_att_mtu_throughput" example with version s140 6.0.0-6alpha.
What's the bitrate used in the long range...
