Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
We are testing SPI communication with the nrf5340 Board as the mater and the nrf52840 board as the slave.
The FW applied to nrf5340 is a FW whose normal operation was confirmed...
I have a problem understanding notifications/subscriptions in the BLE context.
I have two devices, Central (nRF5340) and Peripheral (nRF52832). My peripheral provides a...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
I'm building the nrf/samples/openthread/cli sample with the nrf54l15dk/nrf54l15/cpuapp/ns board. The only change I'm making is enabling CONFIG_DEBUG_THREAD_INFO.
The app...
Hello,
I am using an LE audio code "nrf5340_audio" code from nRF SDK v2.8.0 to play a beep tone. I want to play a tone from a temporary memory, so I have created a logic...
I'm following the dev academy lessons and I'm having a bit of an issue where VS Code intellisense isn't picking up on the include paths from zephyr (e.g. #include <zephyr...
Hi, while working with the nRF9160DK i get this Error a lot of times, I can't say "Yes" or something else and have to wait until the progress bar fills completely. Even if...
Hello
Our 52840-based device has a functionality of playing one of 10 pre-recorded phrases via I2S interface. We'd like to be able to update the wording or load a different...
When integrating DTM into my main app, I have to comment out the macro CONFIG_BT=y to ensure the DTM test can run properly after the build. Are there alternative ways to include...
Hi
I am working on nRF54L15-DK (PCA10156 0.9.2 2024.49) with chip N54L15 QFAAB0 2444AA
I am using Nordic SDK 3.0.2 and Zephyr 4.0.99
My task is to have the top 2K of...
Trying to read button 3 on the npm1300-ek, which is gpio 1 according to the schematic. The following #defines represent the gpio related registers on the npm1300:
#define...
I have been using my nRF54L15-DK board since it arrived just fine, however today when I went to flash the firmware I received the following error:
-- west flash: using runner...
Dear All, I am looking to connect to WiFi enterprise AP. So far I have been able to connect to the network using the nrf/samples/wifi/shell using a command that looks like...
