I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hi ,
SDK 17.1.0
SD132
SoC - nrf52832
I am following the below given link to create custom service.
https://github.com/bjornspockeli/custom_ble_service_example...
We plan to use it with the Converter mode enabled for low current consumption.
However, if PIN is always set to Hi in order to use the Converter mode, about 300ÎĽA will...
After a lot of thought about the issues with TCP under EDRX or PSM , I have a feature request.
I would like if the application layer could know when a TCP socket was sitting...
Hi Nordic team
I tried ncs 1.9.0 peripheral_uart sample (\TOOLCHAIN\v1.9.0\nrf\samples\bluetooth\peripheral_uart) at PCA10095 v1.0.0 DK.
1. Application core: Board is...
Hi, I'm trying to get started with unit testing in Zephyr by running the sample in samples/subsys/testsuite/integration. I'm using ncs 1.7.1.
I copied the sample to my workspace...
System details:
Board: Custom
Chip: nRF52832
PCA Number: PCA10040
SoftDevice: S132
SDK: Version 16.0.0
Until recently, I have had no issues using the TWI module...
I use nRF52840 in aQFN73 package. Can I assign QSPI contacts to G1, J1, L1, N1, R1, U1 pins? Or should I strictly follow the recommendations from the datasheet? Thanks.
Hi All,
I have an application that wants to send 1 array every 2ms. There are 10Bytes of data in the array.
I will be based on 1Mbps, MTU size = 23byte, Payload = 27byte...
Dear Sirs,
I use the standard printf() function to communicate via UART (with retargeting).
Unfortunately could not find a way to not overwrite a buffer.
The only workaround...
I have configured EasyDMA RX.MAXCNT=256 and set EVENTS_ENDRX. If >=256 bytes arrive, an interrupt occurs immediately. And if only 128 or 10 or 203 come.. byte, then I'll never...
Hi,
I'm using nRF Connect SDK 1.7.1.
Is it possible to mix polling & interrupt driven UART API?
I have a situation in which I want to receive input once in a while...
Hello,
I am using the Bluetooth Low Energy application to interact with my device under development. I notice that if I set the Write No Response property on an attribute...
Hello, I have recently started an evaluation on nRF9160 DK in the UK. I tried to run the Serial LTE or AT Client examples but I was not lucky to register to a network. Using...
