When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
We feed the nRF54LM20A’s VBUS pin (the USB high-speed PHY) from the nPM1300’s VBUSOUT, so that the PMIC’s input protection guards the module and the processor sees VBUS only...
With PM device runtime enabled ( CONFIG_PM_DEVICE_RUNTIME =y ), calling uart_irq_tx_disable (actual driver function uarte_nrfx_irq_tx_disable) may result in increase the PM...
So far, 10,000 chips have been produced. More than 100 chips encountered the situation where there was no pwm output at pin P0.20. The program is the same. A multimeter was...
Hello:
Hello Nordic Support,
We are developing a battery-powered product based on the nPM2100 and nRF54L15 , powered by either a CR2032 or CR2450 primary coin-cell battery...
I'm in the early stages of building a Thread + CoAP low-power sensor and using the nRF54L15-Tag as a starting point. Using NCS, the lowest idle current I can get is 13 microamps...
I'm working on an open source smart watch project https://github.com/Protocentral/healthypi-move-fw . I'm after serial communication with another device, so I need to re-enable...
Hello,
I am experiencing an issue with my nRF52 DK. The target nRF52832 appears to be working, but the on-board debugger is not functioning.
Symptoms:
No power/debug...
The "Programmer v4.8.0" from "nRF Connect for Desktop v5.4.0" does not appear to use the Windows system time correctly, and this problem has appeared for us with the new UTC...
Hello,
Recently we're planning to start our nRF-9151 custom board production.
I've designed my own PC program to confirm all the connectors out application used are doing...
Dear Nordic, We are testing NTN NB-IoT on an nRF9151 DK against an Amarisoft callbox. We'd like to see how the modem finds the cell and estimates Doppler and timing before...
Hello,
after having a product using a nrf52832 MCU for a while in production using nrf connect sdk 2.5.1, we now wanted to supply a first firmware update. However, while...
Looking the nRF7002 reference schematics in the datasheet and I'm wondering if you really have to use so many different capacitor values for decoupling. I would like to harmonize...
During reset and initialization are the NFC pins configured as GPIO or as NFC?
If they are in NFC mode can you clarify if they have any special behavior on boot (pulls,...
We are currently evaluating the nrf9151 via the thingy91X
for our application we need the device to function in areas with no cell coverage and not drain the battery....
We will like to use the Nordic nRF9151 to verify our CP-EDT feature. For that we need an AT command to trigger MO ping but we have not been able to find such command in your...
