I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
1) what is the touch pad IC driver that will support nRF52840 ?
2) S25FL512s compactible with nRF52840 as an external nor flash interface . if yes how to get started with...
I am using nRF Sniffer/Wireshark to diagnose some problems with a custom app using 128 bit Service UUIDs as well as well known 16-bit UUIDs.
In the screenshot below, you...
Hi,
Based on previous threads on the matter:
https://devzone.nordicsemi.com/f/nordic-q-a/46565/sdk-15-3-0-missing-bootloader-definitions-for-nrf52832_xxab-qfab
https...
HI
We are using nrf connect sdk.
We understand that when we put the nrf in power down and if any interrupt comes in any gpio than it will reset and wake up.
But my question...
Hello everyone,
im quite new to nrf52.
i m trying to fecth the ADC value on teraterm. but it is not showing the expected output.
please help..
thanx in advance.
Hi,
I am trying to modify the multilink central example to send string to other board.
In the main.c I inserted the uart_init(), uart_event_handle() methods
I added...
While developing a set of C++ tools to simplify configuring and managing BLE on NRF52 chips, I've encountered an error code returned from the advertising module's ble_advertising_start...
Hi, I have several services running in the application. one of them is DFU.
I have to hide / stop DFU service for example when the SOC of the battery is less than 50%. And...
Hi,
I am working on nrF52832 as a gatt peipheral (server)and have a requirement to send 12KB of data over a custom service. I have done the following:
1. Created a custom...
Hi Nordic:
1. Does NRF9160 modem 1.3.1 support CSQ command?
2 Is there a command to get SINR signal?
3. NCSv1.8.0, modem1.3.1 %XRFTEST (AT%XRFTEST=2,1,0,0) Can it can...
Hi,
we're performing an evaluation of using an nRF528xx module with 802.15.4 stack to replace a 3rd-party radio module. There will need to be an AT command protocol for...
Hi i am using nordic nrf52840 chip. and SDK17.1 i am using.
in that under secure bootloader code i am trying to use the nrf_crypto_hash_update() function to calculate...
Hi,
We need to update the firmware of the device through IOS-nRF-Connect-Device-Manager, but the language currently used in our old project is objective-c. IOS-nRF-Connect...
hello ,
We use the nRF9160‘s GPS. We see that the 9160 Thingy use a GPS LNA between the 9160 module and the 9160 GPS antenna?
We want to know, whether we can do...
Hi,
I know that the Bluetooth mesh cannot use long range, but I want to know whether the output power of the node can be controlled to adjust its broadcast range？
Thanks...
